Brother International HE-800A Instruction Manual - English - Page 75

Thread breakage before sewing is finished

Get Brother International HE-800A PDF manuals and user guides View all Brother International HE-800A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

8. SEWING ８-４. Thread breakage before sewing is finished If the thread breaks just before sewing is complete, and then sewing is completed without the thread breakage being detected, the following operations are possible. Note: This is enabled when panel DIP switch A - No. 1 is set to ON. Even if sewing is complete, leave the work clamp lowered and check the sewing. Then depress the treadle backward to trim the thread and raise the work clamp. 3966Q To finish sewing in this condition [Finish] 1. Press the RESET key (1). The needle zigzag and feed mechanisms will return to the sewing start position, and the work clamp will rise. 2. Sewing will start again when the treadle is depressed. To start sewing again from slightly before or after the thread breakage [Resuming sewing] 1. Press the parameter DOWN key (2) to move the zigzag and feed mechanisms to the position to continue sewing from. 2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation. 3. Depress the treadle. The rest of the sewing will be carried out. 4. After sewing is complete, depress the treadle backward. * The thread will be trimmed and the work clamp will be raised. 5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation. To sew from the sewing start point without raising the work clamp (without shifting the material) [Re-sewing] 1. While pressing the parameter DOWN key (2), press the RESET key (1). * The needle zigzag and feed mechanisms will return to the sewing start position, but the work clamp will not rise. 2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation. 3. Depress the treadle to start sewing. 4. After sewing is complete, depress the treadle backward. * The thread will be trimmed and the work clamp will be raised. 5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation. To sew from the sewing start point without raising the work clamp in the other program (without shifting the material) [Re-sewing in the other program] The other program number can be retrieved when re-sewing. (For example, if there is a program which has already been assigned to a different program number which has the same buttonhole shape and which has underlays sewn together as an added function, then you can retrieve that program.) 1. Press the Program No. keys (4) or (5) to select the program, and then press the ENTER key (6). 2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation. 3. Depress the treadle to start sewing. 4. After sewing is complete, depress the treadle backward. * The thread will be trimmed and the work clamp will be raised. 5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation. 6. Return the program number to the previous number. 67 HE-800A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
HE-800A
8. SEWING
67
８
-
４
. Thread breakage before sewing is finished
If the thread breaks just before sewing is complete, and then sewing is completed without the thread breakage being
detected, the following operations are possible.
Note:
This is enabled when panel DIP switch A - No. 1 is set to ON.
Even if sewing is complete, leave the work clamp lowered and check the sewing. Then depress the treadle
backward to trim the thread and raise the work clamp.
To finish sewing in this condition
[
Finish]
1. Press the RESET key (1). The needle zigzag and feed mechanisms will return to the sewing start position, and the
work clamp will rise.
2. Sewing will start again when the treadle is depressed.
To start sewing again from slightly before or after the thread breakage [Resuming sewing]
1. Press the parameter DOWN key (2) to move the zigzag and feed mechanisms to the position to continue sewing
from.
2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation.
3. Depress the treadle. The rest of the sewing will be carried out.
4. After sewing is complete, depress the treadle backward.
* The thread will be trimmed and the work clamp will be raised.
5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation.
To sew from the sewing start point without raising the work clamp (without shifting the material)
[Re-sewing]
1. While pressing the parameter DOWN key (2), press the RESET key (1).
* The needle zigzag and feed mechanisms will return to the sewing start position, but the work clamp will not rise.
2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation.
3. Depress the treadle to start sewing.
4. After sewing is complete, depress the treadle backward.
* The thread will be trimmed and the work clamp will be raised.
5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation.
To sew from the sewing start point without raising the work clamp in the other program (without shifting the
material) [Re-sewing in the other program]
The other program number can be retrieved when re-sewing. (For example, if there is a program which has already
been assigned to a different program number which has the same buttonhole shape and which has underlays sewn
together as an added function, then you can retrieve that program.)
1. Press the Program No. keys (4) or (5) to select the program, and then press the ENTER key (6).
2. If you do not want the cutter to operate, press the CUTTER ON key (3) to disable cutter operation.
3. Depress the treadle to start sewing.
4. After sewing is complete, depress the treadle backward.
* The thread will be trimmed and the work clamp will be raised.
5. Before carrying out the next sewing operation, press the CUTTER ON key (3) to enable cutter operation.
6. Return the program number to the previous number.
3966Q