Brother International PT-9600 Service Manual - Page 77

Reassembling the Half Cutter Chassis ASSY

Page 77 highlights

Reassembling the Half Cutter Chassis ASSY (1) Fit the cutter sensor PCB ASSY to the positioning pins and secure it on the half cutter chassis ASSY with two screws. (2) Fit the HC support plate to the positioning pins and secure it on the half cutter chassis ASSY with two screws. Half cutter chassis ASSY Positioning pin Cutter sensor PCB ASSY Positioning pin HC support plate Screws Positioning pin Screws Fig. 3.2-24 Reassembling the Half Cutter Chassis ASSY (1) (3) Fit the half cutter chassis ASSY to the positioning pins in two places and secure it on the chassis ASSY with six screws. Warning: Take care not to get injured in your fingers with the cutter blade. Note: Apply the silicon grease (Shin-Etsu Chemical brand G501) by a half rice-grain sized drop with a brush on "A" portion of control plate. Screws "A" Screws Take care not to get this plane stained with grease. Half cutter chassis ASSY Chassis ASSY Positioning pins Fig. 3.2-25 Reassembling the Half Cutter Chassis ASSY (2) III-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165

III-43
Reassembling the Half Cutter Chassis ASSY
(1)
Fit the cutter sensor PCB ASSY to the positioning pins and secure it on the half cutter
chassis ASSY with two screws.
(2)
Fit the HC support plate to the positioning pins and secure it on the half cutter chassis ASSY
with two screws.
Fig. 3.2-24
Reassembling the Half Cutter Chassis ASSY (1)
(3)
Fit the half cutter chassis ASSY to the positioning pins in two places and secure it on the
chassis ASSY with six screws.
Warning:
Take care not to get injured in your fingers with the cutter blade.
Note: Apply the silicon grease (Shin-Etsu Chemical brand G501) by a half rice-grain sized
drop with a brush on “A” portion of control plate.
Fig. 3.2-25
Reassembling the Half Cutter Chassis ASSY (2)
Positioning pin
Positioning pin
Positioning pin
Screws
Half cutter chassis ASSY
HC support plate
Cutter sensor PCB ASSY
Screws
Take care not to get this
plane stained with grease.
“A”
Half cutter chassis ASSY
Positioning pins
Chassis ASSY
Screws
Screws