Brother International PT-9600 Service Manual - Page 97

Half Cutter Adjustment Mode 5 key

Get Brother International PT-9600 PDF manuals and user guides
UPC - 012502602774
View all Brother International PT-9600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

2.5. Half Cutter Adjustment Mode ( " 5 " key ) This mode checks the half cut function. Fig. 14 (1) Press the "RET" key. The display shifts to one as shown in Fig.15. Fig. 15 (2) Press the "1" key. The display shifts to the Print Mode 1 that enables to set and print the sample print to examine the cutter blade length. (3) Press the numeric keys to enter the cutting range and step length. (4) The entered value is fixed by pressing the "RET" key and then the sample printing is started. After the completion of printing, the display returns to the initial display of the setting-item selection. Note 1: Press only the "RET" key to start the sample printing, if you accept the default setting values. Note 2: To determine the sample print quality, set the feed length of the tape to 30 mm and reduce the step length from 200 to 160 by 5 steps. The acceptable print quality should be one to be hardly observed a tiny cutting scar at step 200. See the print sample shown in Fig.16. The half cut should be located below the numerical figure. (Example: Step 200 through step 160) Fig. 16 III-63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
III-63
2.5.
Half Cutter Adjustment Mode ( “ 5 ” key )
This mode checks the half cut function.
Fig. 14
(1)
Press the “RET” key.
The display shifts to one as shown in Fig.15.
Fig. 15
(2)
Press the “1” key.
The display shifts to the Print Mode 1 that enables to set and print
the sample print to examine the cutter blade length.
(3)
Press the numeric keys to enter the cutting range and step length.
(4)
The entered value is fixed by pressing the “RET” key and then the sample printing is
started.
After the completion of printing, the display returns to the initial display of the
setting-item selection.
Note 1: Press only the “RET” key to start the sample printing, if you accept the default
setting values.
Note 2: To determine the sample print quality, set the feed length of the tape to 30 mm
and reduce the step length from 200 to 160 by 5 steps.
The acceptable print
quality should be one to be hardly observed a tiny cutting scar at step 200.
See
the print sample shown in Fig.16.
The half cut should be located below the
numerical figure.
(Example: Step 200 through step 160)
Fig. 16