Brother International SE725 Operation Manual - Page 22

catch on the slit in the spool or the machine

Get Brother International SE725 PDF manuals and user guides View all Brother International SE725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Winding/Installing the Bobbin Remove the spool cap and place the spool of thread for b the bobbin onto the spool pin. Slide the spool onto the spool pin so that the thread unwinds to the front from the bottom. 1 1 The thread unwinds to the front from the bottom. Slide the spool cap onto the spool pin. c Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left. Note • When using the spool as shown below, use the thread spool insert (mini king thread spool). Make sure that the thread spool insert is firmly inserted. After installing it, pull out some thread, and check that the thread unwinds without getting caught. 1 Thread spool insert (mini king thread spool) 2 Hole diameter 8.0 mm to 10.5 mm (5/16 inch to 13/32 inch) 3 Spool (crosswound thread) IMPORTANT • If the spool or the spool cap is not installed correctly, the thread may become tangled around the spool pin, and the machine may be damaged. • Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the machine may be damaged. When using mini king thread spool, use the thread spool insert (mini king thread spool). • When using thread that winds off quickly, such as transparent nylon thread or metallic thread, place the spool net over the spool before placing the spool of thread onto the spool pin. If the spool net is too long, fold it to fit the size of the spool. While holding the pulled-out thread so that there is no d slack in it, pass the thread under the hook of the thread guide, then under the thread guide cover and to the front. a b 1 Thread guide 2 Thread guide cover Pass the thread under the hook on the bobbin winding e thread guide, and then wind it counterclockwise under the pretension disk. 1 2 3 1 Bobbin winding thread guide 2 Pretension disk 3 Pull it in as far as possible Note • Make sure that the thread is passed under the pretension disk. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Winding/Installing the Bobbin
20
b
Remove the spool cap and place the spool of thread for
the bobbin onto the spool pin.
Slide the spool onto the spool pin so that the thread
unwinds to the front from the bottom.
1
The thread unwinds to the front from the bottom.
c
Slide the spool cap onto the spool pin.
Slide the spool cap as far as possible to the right, as
shown, with the rounded side on the left.
d
While holding the pulled-out thread so that there is no
slack in it, pass the thread under the hook of the thread
guide, then under the thread guide cover and to the
front.
1
Thread guide
2
Thread guide cover
e
Pass the thread under the hook on the bobbin winding
thread guide, and then wind it counterclockwise under
the pretension disk.
1
Bobbin winding thread guide
2
Pretension disk
3
Pull it in as far as possible
IMPORTANT
•
If the spool or the spool cap is not installed
correctly, the thread may become tangled
around the spool pin, and the machine may be
damaged.
•
Three spool cap sizes are available, allowing
you to choose a spool cap that best fits the size
of spool being used. If the spool cap is too
small for the spool being used, the thread may
catch on the slit in the spool or the machine
may be damaged. When using mini king thread
spool, use the thread spool insert (mini king
thread spool).
1
Note
•
When using the spool as shown below, use the
thread spool insert (mini king thread spool).
Make sure that the thread spool insert is firmly
inserted. After installing it, pull out some thread,
and check that the thread unwinds without getting
caught.
•
When using thread that winds off quickly, such as
transparent nylon thread or metallic thread, place
the spool net over the spool before placing the
spool of thread onto the spool pin.
If the spool net is too long, fold it to fit the size of
the spool.
Note
•
Make sure that the thread is passed under the
pretension disk.
1
Thread spool insert
(mini king thread
spool)
2
Hole diameter
8.0 mm to 10.5 mm
(5/16 inch to 13/32
inch)
3
Spool (cross-
wound thread)
a
b
1
2
3