Brother International SE725 Operation Manual - Page 24

Installing the bobbin

Get Brother International SE725 PDF manuals and user guides View all Brother International SE725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Winding/Installing the Bobbin Installing the bobbin Install the bobbin wound with thread. You can begin sewing immediately without pulling up the bobbin thread by simply inserting the bobbin in the bobbin case and guiding the thread through the slit in the needle plate cover. Memo • If the threads will be pulled to create gathers or the thread at the beginning of sewing will be finished, for example, when free motion quilting, first pull up the bobbin thread. For details, refer to "Pulling up the bobbin thread" on page 26. Slide the bobbin cover latch to the right and remove e the bobbin cover. Insert the bobbin into the bobbin case so that the f thread unwinds to the left. CAUTION • Use a bobbin that has been correctly wound with thread, otherwise there is a risk of poor thread tension or injury due to the needle breaking. • Before inserting or changing the bobbin, be sure that you have touched on the operation panel to lock all keys and buttons, otherwise injuries may occur if the "Start/ Stop" button or any other button is pressed and the machine starts. Turn on the machine. a Press (Needle position button) once or twice to b raise the needle. Touch . c  The screen changes, and all keys and operation buttons are locked (except ). Memo • For the correct winding direction of the bobbin thread, be sure to place the bobbin into the bobbin case in the same orientation that it was on the bobbin winder shaft. The "b" mark on one side of the bobbin included with this machine can be used as a reference. Lightly hold down the bobbin with your right hand g (1), and then guide the end of the thread around the tab of the needle plate cover with your left hand (2). 1 Tab Raise the presser foot lever. d Note • Be sure to hold down the bobbin with your finger and unwind the bobbin thread correctly, otherwise the thread may break or the thread tension will be incorrect. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Winding/Installing the Bobbin
22
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Turn on the machine.
b
Press
(Needle position button) once or twice to
raise the needle.
c
Touch
.
The screen changes, and all keys and operation
buttons are locked (except
).
d
Raise the presser foot lever.
e
Slide the bobbin cover latch to the right and remove
the bobbin cover.
f
Insert the bobbin into the bobbin case so that the
thread unwinds to the left.
g
Lightly hold down the bobbin with your right hand
(
1
), and then guide the end of the thread around the
tab of the needle plate cover with your left hand (
2
).
Memo
•
If the threads will be pulled to create gathers or the
thread at the beginning of sewing will be finished,
for example, when free motion quilting, first pull up
the bobbin thread.
For details, refer to “Pulling up the bobbin thread”
on page 26.
CAUTION
•
Use a bobbin that has been correctly wound
with thread, otherwise there is a risk of poor
thread tension or injury due to the needle
breaking.
•
Before inserting or changing the bobbin, be
sure that you have touched
on the
operation panel to lock all keys and buttons,
otherwise injuries may occur if the “Start/
Stop” button or any other button is pressed
and the machine starts.
Memo
•
For the correct winding direction of the bobbin
thread, be sure to place the bobbin into the bobbin
case in the same orientation that it was on the
bobbin winder shaft.
The “b” mark on one side of the bobbin included
with this machine can be used as a reference.
1
Tab
Note
•
Be sure to hold down the bobbin with your finger
and unwind the bobbin thread correctly, otherwise
the thread may break or the thread tension will be
incorrect.