Canon REALiS LCOS SX80 SX80 Manual - Page 119

If You Want to Reset the Network Setting, Error Notification Message

Get Canon REALiS LCOS SX80 PDF manuals and user guides View all Canon REALiS LCOS SX80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Setting an IP Address 6 Click [Apply] in the menu. When "Save and apply settings. OK?" message appears, click the [OK] button. This completes the IP address setting of the projector. ■If You Want to Reset the Network Setting 1 Access to the projector from web browser by performing the step 1 on "Setting Net- work (P117)." 2 Click [Initialize] in the network setting page. 3 Click the [OK] button when "Initialize network settings?" message appears. • To restore the settings with the projector operation, execute [Network setting initialization] from the menu. ■Error Notification Message If errors occur in the projector, the following messages are sent. Error list Error name Errors related to temperature Text Errors related to the lamp Error name Text Errors related to the lamp cover Error name Text Errors related to the cooling fan Error name Text Errors related to the power supply Error name Text Other types of errors Error name Text Temperature abnormality The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection. If the same warning occurs again, the projector may be defective. Contact your dealer. Faulty lamp The lamp has burnt out. Replace the lamp with a new one. If the same warning occurs again, the lamp drive circuit may be defective. Contact your dealer. Faulty lamp cover The lamp cover is open. Check whether the lamp cover is installed properly. If it is installed properly, the lamp cover detection switch may be defective. Contact your dealer. Faulty cooling fan The cooling fan or another component may be defective. Contact your dealer. Faulty power supply The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply. Contact your dealer. Unknown Error Codes in hexadecimal numbers* * Contact your Canon dealer. Operating the Projector over Network 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
119
Setting an IP Address
Operating the Projector over Network
6
Click [Apply] in the menu.
When "Save and apply settings. OK?" message appears,
click the [OK] button.
This completes the IP address setting of the projector.
■
If You Want to Reset the Network Setting
1
Access to the projector from web browser by performing the step 1 on “Setting Net-
work (
P117
).”
2
Click [Initialize] in the network setting page.
3
Click the [OK] button when “Initialize network settings?” message appears.
•
To restore the settings with the projector operation, execute [Network setting initial-
ization] from the menu.
■
Error Notification Message
If errors occur in the projector, the following messages are sent.
Error list
* Contact your Canon dealer.
Errors related to
temperature
Error name
Temperature abnormality
Text
The temperature inside the projector is too high for some
reason or the outside air temperature is higher than the
specified one. If the problem is inside the projector,
check whether the projector is installed and operated
normally, turn off the projector to cool its inside, and retry
projection. If the same warning occurs again, the projec-
tor may be defective. Contact your dealer.
Errors related to
the lamp
Error name
Faulty lamp
Text
The lamp has burnt out. Replace the lamp with a new
one. If the same warning occurs again, the lamp drive
circuit may be defective. Contact your dealer.
Errors related to
the lamp cover
Error name
Faulty lamp cover
Text
The lamp cover is open. Check whether the lamp cover
is installed properly. If it is installed properly, the lamp
cover detection switch may be defective. Contact your
dealer.
Errors related to
the cooling fan
Error name
Faulty cooling fan
Text
The cooling fan or another component may be defective.
Contact your dealer.
Errors related to
the power supply
Error name
Faulty power supply
Text
The voltage of part of the power supply is abnormally
high or any other problem has occurred in the power
supply. Contact your dealer.
Other types of
errors
Error name
Unknown Error
Text
Codes in hexadecimal numbers*