Cub Cadet XT2 SLX54 Operation Manual - Page 11

Operation

Get Cub Cadet XT2 SLX54 PDF manuals and user guides View all Cub Cadet XT2 SLX54 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

OPERATION 4a 13 4b 4 3 4c 16 14 15 12 71 5 11 8 2 9 6 17 10 Figure 26 Note: This Operator's Manual covers several models. Tractor features may vary by model. Not all features in this manual are applicable to all tractor models and the tractor depicted may differ from yours. Note: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the tractor when facing forward while seated in the operator's seat. 1 Forward Drive Pedal Depress the forward drive pedal forward to allow the tractor to travel forward. The further forward the pedal is depressed, the faster the tractor will travel. The pedal will return to its original/neutral position when it's not depressed. 2 Reverse Drive Pedal Depress the reverse drive pedal downward to allow the tractor to travel backward. The further downward the pedal is depressed, the faster the tractor will travel. The pedal will return to its original/neutral position when it's not depressed. 3 Brake Pedal Depress the brake pedal while the tractor is in use to stop the tractor and for setting the parking brake. Note: The brake pedal must be fully depressed to start the tractor. Refer to Safety Interlock System for more information. 4 Throttle/Choke Control Lever, Throttle Control, or Electronic Governor Control 4a Throttle/Choke Control Lever (If equipped) Push the throttle/choke control lever forward to increase the engine speed. The tractor is designed to operate with the throttle/choke control lever at full throttle (FAST) when the tractor is being driven and the mower deck is engaged. Pull the throttle/choke control lever rearward to decrease the engine speed. Whenstartingthe engine,pushthecontrolleverfullyforwardintothe"CHOKE"position.After starting and warming the engine, move the control lever rearward until you feel it move past the choke detent. Throttle is not meant to control unit speed, throttle should remain in high speed while operating blades. 4b Throttle Control (If equipped) Push the throttle control lever forward to increase the engine speed. The tractor is designed to operate with the throttle control lever at full throttle (FAST) when the tractor is being driven and the tractor deck is engaged. Pull the throttle control lever rearward to decrease the engine speed. 4c Electronic Governor Control (If equipped) When set in a given position, a uniform engine speed will be maintained. The electronic governor control has various inputs for maintaining engine speed. Use "CUT" setting for optimal cutting performance in normal cutting conditions. Use "POWER CUT" setting for optimal cutting performance in heavy cutting conditions. Note: If the tractor is equipped with an Electronic Governor Control, the tractor can be started at any speed setting along the dial and will automatically adjust to the desired engine speed setting. Note: It may take a few seconds after starting for the engine to adjust to the proper engine speed. This is normal. 5 Choke Control (If equipped) The choke control determines the position of the engine choke. Pull the knob out to choke the engine; push the knob in to open the choke. If equipped, Choke Control will be paired with a Throttle Control (4b). When pulled outward the Choke Control closes the choke for cold starting. Once started always run the engine with the Choke Control pushed all the way inward. 6 Deck Lift Lever The deck lift lever is used to raise and lower the deck. Pull the lever to the left out of the index notch and push downward to lower the deck, or pull upward to raise the deck. When the desired height is attained, move the lift lever to the right until fully engaged in the index notch. 7 Ignition Switch Turn-Key Start WARNING Never leave a running tractor unattended. Always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting. Refer to Starting the Engine for information on how to start the engine. Refer to Stopping the Engine for instructions on how to stop the engine. WARNING Prior to operating the tractor, refer to both Safty Interlock System and Starting The Engine in the Operation section of this manual for detailed instructions regarding the Ignition Switch Module and operating the tractor in REVERSE CAUTION MODE. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
11
OPERATION
1
4
5
6
14
7
8
9
11
12
13
10
2
3
4a
4b
4c
15
16
17
Figure 26
Note:
This Operator’s Manual covers several models. Tractor features may vary by
model. Not all features in this manual are applicable to all tractor models and the
tractor depicted may differ from yours.
Note:
References to LEFT, RIGHT, FRONT, and REAR indicate that position on the
tractor when facing forward while seated in the operator’s seat.
1
Forward Drive Pedal
Depress the forward drive pedal forward to allow the tractor to travel forward. The
further forward the pedal is depressed, the faster the tractor will travel. The pedal will
return to its original/neutral position when it’s not depressed.
2
Reverse Drive Pedal
Depress the reverse drive pedal downward to allow the tractor to travel backward. The
further downward the pedal is depressed, the faster the tractor will travel. The pedal will
return to its original/neutral position when it’s not depressed.
3
Brake Pedal
Depress the brake pedal while the tractor is in use to stop the tractor and for setting
the parking brake.
Note:
The brake pedal must be fully depressed to start the tractor. Refer to Safety
Interlock System for more information.
4
Throttle/Choke Control Lever, Throttle Control, or
Electronic Governor Control
4a
Throttle/Choke Control Lever (If equipped)
Push the throttle/choke control lever forward to increase the engine speed. The
tractor is designed to operate with the throttle/choke control lever at full throttle
(FAST) when the tractor is being driven and the mower deck is engaged. Pull the
throttle/choke control lever rearward to decrease the engine speed. When starting the
engine, push the control lever fully forward into the “CHOKE” position. After starting and
warming the engine, move the control lever rearward until you feel it move past the
choke detent. Throttle is not meant to control unit speed, throttle should remain in
high speed while operating blades.
4b
Throttle Control (If equipped)
Push the throttle control lever forward to increase the engine speed. The tractor is
designed to operate with the throttle control lever at full throttle (FAST) when the
tractor is being driven and the tractor deck is engaged. Pull the throttle control lever
rearward to decrease the engine speed.
4c
Electronic Governor Control (If equipped)
When set in a given position, a uniform engine speed will be maintained.
The electronic governor control has various inputs for maintaining engine speed.
Use “CUT” setting for optimal cutting performance in normal cutting conditions. Use
“POWER CUT” setting for optimal cutting performance in heavy cutting conditions.
Note:
If the tractor is equipped with an Electronic Governor Control, the tractor can be
started at any speed setting along the dial and will automatically adjust to the desired
engine speed setting.
Note:
It may take a few seconds after starting for the engine to adjust to the proper
engine speed. This is normal.
5
Choke Control (If equipped)
The choke control determines the position of the engine choke.
Pull the knob out to choke the engine; push the knob in to open
the choke. If equipped, Choke Control will be paired with a Throttle
Control (4b). When pulled outward the Choke Control closes the
choke for cold starting. Once started always run the engine with
the Choke Control pushed all the way inward.
6
Deck Lift Lever
The deck lift lever is used to raise and lower the deck. Pull the lever to the left out of
the index notch and push downward to lower the deck, or pull upward to raise the
deck. When the desired height is attained, move the lift lever to the right until fully
engaged in the index notch.
7
Ignition Switch
Turn-Key Start
WARNING
Never leave a running tractor unattended.
Always disengage PTO, set parking brake,
stop engine and remove key to prevent
unintended starting.
Refer to Starting the Engine for information
on how to start the engine. Refer to Stopping
the Engine for instructions on how to stop the
engine.
WARNING
Prior to operating the tractor, refer to both
Safty Interlock System
and
Starting The Engine
in the Operation section of this manual for detailed
instructions regarding the Ignition Switch Module and operating the tractor
in
REVERSE CAUTION MODE
.