D-Link DHP-W307AV User Manual - Page 52

Con WEP

Get D-Link DHP-W307AV PDF manuals and user guides View all D-Link DHP-W307AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (192.168.0.50). Click on Setup and then click Wireless Settings on the left side. 2. Next to Security Mode in the Wireless Security Mode section, select Enable WEP Wireless Security (Basic). 3. Next to Authentication, select Open or Shared Key. 4. Next to WEP Encryption, select 64-bit or 128-bit encryption. 5. Next to Key Type, select either Hex or ASCII. Hex (recommended) - Letters A-F and numbers 0-9 are valid. ASCII - All numbers and letters are valid. 6. Next to Key 1, enter a WEP key that you create. Make sure you enter this key exactly on all your wireless devices. You may enter up to 4 different keys. 7. Click Save Settings at the top of the window to save your settings. If you are configuring the access point with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the access point. D-Link DHP-W307AV User Manual 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
52
D-Link DHP-W307AV User Manual
Section 4 - Security
Configure WEP
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the
added overhead.
1. Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50).
Click on
Setup
and then click
Wireless Settings
on the left side.
2. Next to Security Mode in the Wireless Security Mode section,
select
Enable WEP Wireless Security (Basic)
.
3. Next to
Authentication
, select
Open
or
Shared Key
.
4. Next to
WEP Encryption
, select
64-bit
or
128-bit
encryption.
5. Next to
Key Type
, select either
Hex
or
ASCII
.
Hex (recommended) - Letters A-F and numbers 0-9 are valid. ASCII
- All numbers and letters are valid.
6. Next to Key 1, enter a WEP key that you create. Make sure you
enter this key exactly on all your wireless devices. You may enter
up to 4 different keys.
7. Click
Save Settings
at the top of the window to save your settings. If you are configuring the access point with a wireless
adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the
access point.