D-Link DXS-1100-10TS User Manual

D-Link DXS-1100-10TS Manual

Get D-Link DXS-1100-10TS PDF manuals and user guides View all D-Link DXS-1100-10TS manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DXS-1100-10TS manual content summary:

  • D-Link DXS-1100-10TS | User Manual - Page 1
  • D-Link DXS-1100-10TS | User Manual - Page 2
    either the entities claiming the marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than and, if not installed and used in accordance with this manual, may cause harmful interference to radio communications. Operation of this
  • D-Link DXS-1100-10TS | User Manual - Page 3
    Safety Compliance Warning: Class 1 Laser Product. • EN: When using a fiber optic media expansion module, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on. • FR: Ne regardez jamais le laser tant qu'il
  • D-Link DXS-1100-10TS | User Manual - Page 4
    DXS-1100 Series 10 Gigabit Ethernet Switch User Manual Table of Contents ...i Intended Readers...1 Terms/Usage...1 Safety Instructions ...1 General Precautions for Rack-Mountable Products 2 Protecting Against Electrostatic Discharge ...3 1 Product Introduction ...4 DXS-1100-10TS...5 Front
  • D-Link DXS-1100-10TS | User Manual - Page 5
    Table of Contents D-Link 10 Gigabit Ethernet Switch User Manual Reboot System ...26 Tool Bar > Wizard ...26 Tool Bar Web ...48 Management > Session Timeout ...49 Management > File System ...49 Management > D-Link Discovery Protocol 50 L2 Features > FDB > Static FDB > Unicast Static FDB 51 L2
  • D-Link DXS-1100-10TS | User Manual - Page 6
    Table of Contents D-Link 10 Gigabit Ethernet Switch User Manual L2 Features > VLAN > Voice VLAN > Voice VLAN Global 58 > STP Port Information 63 L2 Features > Loopback Detection ...63 L2 Features > Link Aggregation ...64 L2 Features > L2 Multicast Control> IGMP Snooping > IGMP Snooping Settings
  • D-Link DXS-1100-10TS | User Manual - Page 7
    Table of Contents D-Link 10 Gigabit Ethernet Switch User Manual Security > SSL > SSL Global Settings ...98 Security > SSL > Crypto PKI Trustpoint 100 Security > SSL > SSL Service Policy...100 OAM > Cable Diagnostics ...101 Monitoring > Utilization > Port Utilization 102 Monitoring > Statistics >
  • D-Link DXS-1100-10TS | User Manual - Page 8
    Ethernet Switch User Manual Intended Readers This guide provides instructions to install the D-Link 10 Gigabit Ethernet Switch DXS-1100-10TS, and to be reviewed and followed. CAUTION: Only trained and qualified service personnel should install, replace or perform maintenance on D-Link switches. To
  • D-Link DXS-1100-10TS | User Manual - Page 9
    Product Introduction D-Link 10 Gigabit Ethernet Switch User Manual o An object has fallen into the product. o The product has been exposed to water. o The product has been dropped or damaged. o The product does not operate correctly when you follow the operating instructions. • Keep your system
  • D-Link DXS-1100-10TS | User Manual - Page 10
    Link 10 Gigabit Ethernet Switch User Manual • Systems are considered to be components in a rack. Thus, "component" refers to any system as well as to various peripherals or supporting Do not step on or stand on any component when servicing other components in a rack. CAUTION: Never defeat the
  • D-Link DXS-1100-10TS | User Manual - Page 11
    versatile management. Flexible Port Configurations. The DXS-1100 series is the new generation of Web 10 Gigabit Ethernet Switch series. It provides a variety of port counts that can operate at up to 10 Gbps wire speed. D-Link Green Technology. D-Link Green devices are about providing eco-friendly
  • D-Link DXS-1100-10TS | User Manual - Page 12
    1 Product Introduction D-Link 10 Gigabit Ethernet Switch User Manual DXS-1100-10TS The DXS-1100-10TS 10 Gigabit Ethernet Switch supports the following ports: • Eight 100/1000/10000Mbps copper Ethernet ports. • Two 1/10Gbps SFP+ module ports. Front Panel Figure 1.1 - DXS-1100-10TS Front Panel
  • D-Link DXS-1100-10TS | User Manual - Page 13
    Ethernet Switch User Manual Fans: Switches in this series have a built-in temperature sensor that will measure the switch's internal temperature and then automatically adjust the speed of the fans to either high-speed or low-speed. DXS-1100-16TC The DXS-1100-16TC 10 Gigabit Ethernet Switch supports
  • D-Link DXS-1100-10TS | User Manual - Page 14
    1 Product Introduction D-Link 10 Gigabit Ethernet Switch User Manual ventilation. Without proper heat dissipation and air circulation, system components might overheat which could lead to system failure or even severely damaged components. Rack-mounting
  • D-Link DXS-1100-10TS | User Manual - Page 15
    Manual to make sure all items are present and undamaged. One D-Link 10 Gigabit Ethernet Switch Guide, Getting Started Guide, and D-Link Network Assistant User Guide. If any item is found missing or damaged, please contact the local reseller for replacement. Step 2: Switch Installation For safe switch
  • D-Link DXS-1100-10TS | User Manual - Page 16
    D-Link 10 Gigabit Ethernet Switch User Manual Figure 2.2 - Attach the mounting brackets to the Switch Then, use the screws provided with the equipment rack to mount the switch in the rack. Figure 2.3 - Mount the Switch in the rack or chassis Please be aware of following safety Instructions when
  • D-Link DXS-1100-10TS | User Manual - Page 17
    2 Hardware Installation D-Link 10 Gigabit Ethernet Switch User Manual E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the
  • D-Link DXS-1100-10TS | User Manual - Page 18
    2 Hardware Installation D-Link 10 Gigabit Ethernet Switch User Manual Figure 2.6 - Slide the Retainer through the Tie Wrap D) Circle the tie of the Retainer around the power cord and into the locker of the Retainer.
  • D-Link DXS-1100-10TS | User Manual - Page 19
    D-Link 10 Gigabit Ethernet Switch User Manual Figure 2.8 - Secure the power cord F) Users may now connect the AC power cord to an electrical outlet (preferably one that is grounded and surge protected). Figure 2.9 - Plugging the switch into an outlet Power Failure As a precaution, the switch
  • D-Link DXS-1100-10TS | User Manual - Page 20
    following installation instructions for the Web-based Management and the D-Link Network Assistant (DNA). Using Web-based Management After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser. Supported Web Browsers
  • D-Link DXS-1100-10TS | User Manual - Page 21
    4 Configuration for detailed instructions. D-Link Network Assistant (DNA) The D-Link Network Assistant (DNA), included in the installation CD, is a program that allows administrators to quickly discover all D-Link smart switches and D-Link Discover Protocol (DDP) supported devices (for a list
  • D-Link DXS-1100-10TS | User Manual - Page 22
    3 Getting Started D-Link 10 Gigabit Ethernet Switch User Manual NOTE: Please be sure to uninstall any existing DNA from your PC before installing the latest DNA. For detailed explanations of the DNA functions, please refer to D-Link Network Assistant (DNA) User Guide. 15
  • D-Link DXS-1100-10TS | User Manual - Page 23
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual 4 Configuration The features and functions of the Switch can be configured for optimum use through the Web-based Management Utility. Smart Wizard Configuration After a successful login, the Smart Wizard will guide you through essential
  • D-Link DXS-1100-10TS | User Manual - Page 24
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual User Accounts Settings Type the desired new username in the User Name field and select the Privilege between User and Administrator. Select Password Type among
  • D-Link DXS-1100-10TS | User Manual - Page 25
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual SNMP The SNMP Setting allows you to quickly enable or disable the SNMP function. The default the Web browser again and make sure your PC is in the same subnet with the switch. See Login Webbased Management for a detailed description. 18
  • D-Link DXS-1100-10TS | User Manual - Page 26
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Web-based Management After clicking Exit in . The Tool Bar provides a quick and convenient way for essential utility functions like firmware and configuration management on the left, and the username with current IP address and the
  • D-Link DXS-1100-10TS | User Manual - Page 27
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Tool Bar > Save Menu The Save Menu provides the Save Configuration function. Figure 4.5 - Save Menu Save Configuration Select to save the entire configuration changes you have made to the device to switch's non-volatile RAM. Figure
  • D-Link DXS-1100-10TS | User Manual - Page 28
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.9 - Tools Menu > Firmware Upgrade and Backup > Firmware Upgrade from HTTP The fields that can be configured are described below: Source File: Click Browse to browse your inventories for a saved firmware file. Destination File:
  • D-Link DXS-1100-10TS | User Manual - Page 29
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Backup to save the firmware to your disk. Firmware Backup to TFTP This window is used to back up the firmware to TFTP. Figure 4.12 - Tools Menu > Firmware Upgrade and Backup > Firmware Backup to TFTP The fields that can be
  • D-Link DXS-1100-10TS | User Manual - Page 30
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Destination File: Enter the destination filename and path where the configuration file should be stored on the Switch. This field can be up to 64 characters long. Select the running-config option to restore and overwrite the running
  • D-Link DXS-1100-10TS | User Manual - Page 31
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.17 - Tools Menu > Configure Restore and Backup Source File: Enter the source filename and path of the configuration file located on the switch here. This field can be up to 64 characters long. Select the running-config option
  • D-Link DXS-1100-10TS | User Manual - Page 32
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.20 - Tools Menu > Log Backup > Log node then responds to or "echoes" the packets sent from the Switch. This is very useful to verify connectivity between the Switch and other nodes on the network. Figure 4.21 - Tools Menu
  • D-Link DXS-1100-10TS | User Manual - Page 33
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.22 -Ping Result Click Stop to halt the Ping Test. Click Back to return to the IPv4 or IPv6 Ping section. Reset Provide a safe reset option for the Switch. Figure 4.23 - Tools Menu > Reset Select the The Switch will be reset to
  • D-Link DXS-1100-10TS | User Manual - Page 34
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Tool Bar > Online Help The Online Help provides two ways of online support: D-Link Support Site will lead you to the D-Link website where you can find online resources such as updated firmware images; User Guide can offer an immediate
  • D-Link DXS-1100-10TS | User Manual - Page 35
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Function Tree All configuration options on the Switch are accessed through the Function Tree. Click the setup item that you want to configure , CPU, and Used status are displayed. It appears automatically when you log in the Switch. 28
  • D-Link DXS-1100-10TS | User Manual - Page 36
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.27 - Device Information System > System Information Settings The System Information Settings allows the user to configure a System Name, System Location, and System Contact to aid in defining the Switch. Figure 4.28 - System >
  • D-Link DXS-1100-10TS | User Manual - Page 37
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are to a PC's NIC using a straight-through cable or a port (in the MDIX mode) on another switch through a cross-over cable. Cross - Select this option for cross cabling. If this option is selected,
  • D-Link DXS-1100-10TS | User Manual - Page 38
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Flow Control: Select to either turn choose from are Auto, and Full. Speed: Select the port speed option here. This option will manually force the connected on the selected port to only connect at the speed specified here. Options to
  • D-Link DXS-1100-10TS | User Manual - Page 39
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.32 - System > Port Configuration > Jumbo Frame size and settings. The Switch supports jumbo frames. Jumbo frames are Ethernet frames with more than 1,536 bytes of payload. The Switch supports jumbo frames with a maximum frame
  • D-Link DXS-1100-10TS | User Manual - Page 40
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.33 - System > Port Configuration > Jumbo Frame The fields that can be configured are described below: From Port / To Port: Select the appropriate port range
  • D-Link DXS-1100-10TS | User Manual - Page 41
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Write Delay: Enter the interval for periodic writing of the logging buffer to FLASH. This value must be between 0 and 65535 seconds. By default, this
  • D-Link DXS-1100-10TS | User Manual - Page 42
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual UDP Port: Specifies the UDP port to which the server logs are sent. This value must be 514, or between 1024 and 65535. The default
  • D-Link DXS-1100-10TS | User Manual - Page 43
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual services, organize the SNTP subnet of servers and clients, and adjust the system clock in each participant. This window is used to configure the time settings for the Switch. Figure 4.39 - System > Time and SNTP > Clock Settings The
  • D-Link DXS-1100-10TS | User Manual - Page 44
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Date Setting - Select to configure the summer > Time and SNTP > SNTP Settings This window is used to configure the time settings for the Switch. Figure 4.41 - System > Time and SNTP > SNTP Settings The fields that can be configured are
  • D-Link DXS-1100-10TS | User Manual - Page 45
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Delete to remove the specified entry. System > Time Range This window and change any of the system configuration settings expressed in this guide. Figure 4.43 - Management > User Accounts Settings (User Management Settings) 38
  • D-Link DXS-1100-10TS | User Manual - Page 46
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described below: User Name: Enter the user account name here. This name can be up to 32 characters
  • D-Link DXS-1100-10TS | User Manual - Page 47
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.46 - Management > SNMP > SNMP Global Settings The fields that can be configured are described below: SNMP Global State: Enable or disable the SNMP feature.
  • D-Link DXS-1100-10TS | User Manual - Page 48
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.47 - Management > SNMP > SNMP Linkchange SNMP notification traps that is generated by the system. Trap State: Enable or disable the SNMP link change trap. Click Apply to accept the changes made. Management > SNMP > SNMP View
  • D-Link DXS-1100-10TS | User Manual - Page 49
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Subtree OID: Enter the Object Identifier (OID) string is used like a password to give remote SNMP managers access to MIB objects in the Switch's SNMP agent. View Name: Enter an alphanumeric string of up to 32 characters that is used
  • D-Link DXS-1100-10TS | User Manual - Page 50
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.50 - Management > SNMP > SNMP Group Table Specify that there will be no authorization and no encryption of packets sent between the Switch and a remote SNMP manager. AuthNoPriv - Specify that authorization will be required, but
  • D-Link DXS-1100-10TS | User Manual - Page 51
    4 Configuration Click Apply to accept the changes made. Management > SNMP > SNMP User Table Settings D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.52 - Management > SNMP > SNMP User Table Settings The fields that can be configured are described below: User Name: Enter an alphanumeric
  • D-Link DXS-1100-10TS | User Manual - Page 52
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.53 - Management > SNMP > SNMP Host monitoring (RMON) for the rising and falling alarm trap feature for the SNMP function on the Switch. Figure 4.54 - Management > RMON > RMON Global Settings The fields that can be configured
  • D-Link DXS-1100-10TS | User Manual - Page 53
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Management > RMON > RMON Statistics Settings This window is used to configure and display the RMON statistics on the specified port. Figure 4.55 - Management > RMON > RMON
  • D-Link DXS-1100-10TS | User Manual - Page 54
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Bucket Number: Enter Specifies the number of buckets specified for the RMON collection history group of statistics. The range is from 1 to 65535. The default
  • D-Link DXS-1100-10TS | User Manual - Page 55
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Add to add a new entry based on the information entered. Click Delete to remove the specified entry. Enter Back to return to the previous window. Management > Web This window is used to configure the Web settings on the Switch. 48
  • D-Link DXS-1100-10TS | User Manual - Page 56
    Link 10 Gigabit Ethernet Switch User Manual Figure 4.62 - Management > Web The fields that can be configured are described below: Port: Enter the TCP port number used for Web-based management of the Switch operation on the Flash. All the firmware, configuration information and system log information
  • D-Link DXS-1100-10TS | User Manual - Page 57
    Link 10 Gigabit Ethernet Switch User Manual Figure 4.65 - Management > File System (Search for Drive) Click Previous to return to the previous window. Click Create Directory to create a new directory within the file system of the Switch. Click Copy to copy a specific file to the Switch this switch,
  • D-Link DXS-1100-10TS | User Manual - Page 58
    10 Gigabit Ethernet Switch User Manual Figure 4.67 - Management > D-Link Discovery Protocol The fields that can be configured are described below: D-Link Discovery Protocol State: Enable or disable DDP global state. Report Timer: Select the interval in seconds between two consecutive DDP report
  • D-Link DXS-1100-10TS | User Manual - Page 59
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual MAC Address: Enter the MAC address to which packets will be statically forwarded or dropped. This must be a unicast MAC address. Click Apply to accept
  • D-Link DXS-1100-10TS | User Manual - Page 60
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.71 - L2 Features > FDB > MAC Address Table Settings (MAC Address Learning) The fields that can be configured are described below: From Port / To Port:
  • D-Link DXS-1100-10TS | User Manual - Page 61
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Find to locate a specific entry based on are described below: MAC Address Notification: Enable or disable MAC notification globally on the Switch. Interval: Enter the time value between notifications. This value must be between 1
  • D-Link DXS-1100-10TS | User Manual - Page 62
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections. The IEEE 802.1Q VLAN Settings
  • D-Link DXS-1100-10TS | User Manual - Page 63
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.76 - L2 Features > VLAN > VLAN Interface Click View Detail to view more detailed information about the VLAN on the specific interface. Click Edit to
  • D-Link DXS-1100-10TS | User Manual - Page 64
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.78 - L2 Features > VLAN > Auto Surveillance VLAN> Auto Surveillance Properties The fields that can be configured are described below: Surveillance VLAN: Enable or disable
  • D-Link DXS-1100-10TS | User Manual - Page 65
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.79 - L2 Features > VLAN > Auto Surveillance VLAN> will be deteriorated if the data is unevenly sent, the quality of service (QoS) for voice traffic shall be configured to ensure the transmission priority of voice packet is
  • D-Link DXS-1100-10TS | User Manual - Page 66
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described Mode: Select the mode of the port. Options to choose from are Auto Untagged, Auto Tagged, and Manual. Click Apply to accept the changes made. L2 Features > VLAN > Voice VLAN > Voice VLAN
  • D-Link DXS-1100-10TS | User Manual - Page 67
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.83 - L2 Features > VLAN > Voice VLAN Voice VLAN > Voice VLAN LLDP-MED Device L2 Features > STP > STP Global Settings The Switch implements two versions of the Spanning Tree Protocol, the Rapid Spanning Tree Protocol (RSTP) as
  • D-Link DXS-1100-10TS | User Manual - Page 68
    D-Link 10 Gigabit Ethernet Switch User Manual settings configured for STP are also used for RSTP. This section introduces some new Spanning Tree concepts and illustrates the main differences between the two protocols. By default, Spanning Tree Protocol is Disabled. If enabled, the Switch will
  • D-Link DXS-1100-10TS | User Manual - Page 69
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual An STP Group spanning tree works in the same way as the switch-level spanning tree, but the root bridge concept is replaced with a root port concept. A root port is a port of the group that is elected based
  • D-Link DXS-1100-10TS | User Manual - Page 70
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual because those bridges are not under the full control of the administrator. When a port is set to the TCN filter mode, the TC event received
  • D-Link DXS-1100-10TS | User Manual - Page 71
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.90 - L2 Features > Loopback > Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The DXS-1100-10TS supports up
  • D-Link DXS-1100-10TS | User Manual - Page 72
    the backbone of a network. The DXS-1100-10TS allows the creation of up to 5 link aggregation groups, each group consisting of 1 to 4 links (ports); and the DXS-1100-16TC allows the creation of up to 8 link aggregation groups, each group consisting of 1 to 8 links (ports). Each port can only belong
  • D-Link DXS-1100-10TS | User Manual - Page 73
    D-Link 10 Gigabit Ethernet Switch User Manual NOTE: If any ports within the trunk group become disconnected, packets intended for the disconnected port will be load shared among the other linked ports of the link aggregation group. This window is used to view and configure the link aggregation
  • D-Link DXS-1100-10TS | User Manual - Page 74
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.93 - L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings The fields that can be configured are described below: Global State: Enable or
  • D-Link DXS-1100-10TS | User Manual - Page 75
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual After clicking Modify or Edit in IGMP Snooping Settings window, the following window will appear. Figure 4.95 - L2 Features > L2 Multicast Control > IGMP Snooping > IGMP
  • D-Link DXS-1100-10TS | User Manual - Page 76
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.96 - L2 Features > L2 Multicast Control > IGMP Snooping as the multicast router ports or as forbidden to be multicast router ports on the Switch. Figure 4.97 - L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping
  • D-Link DXS-1100-10TS | User Manual - Page 77
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Port - Select to have the configured ports to be static multicast router ports. Forbidden Port - 3 part of an MLD control packet transferred between end nodes and a MLD router. When the Switch discovers that this route is requesting 70
  • D-Link DXS-1100-10TS | User Manual - Page 78
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual multicast traffic, it adds the port directly 143 in the ICMP packet header, this message is sent by the listening port to the Switch stating that it is interested in receiving multicast data from a multicast address in response to the
  • D-Link DXS-1100-10TS | User Manual - Page 79
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Edit to re-configure the specific entry. Enter a page number and click Go to navigate to a specific page when multiple pages exist. After clicking
  • D-Link DXS-1100-10TS | User Manual - Page 80
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described below: Minimum Version: Select the minimum version of MLD hosts that is allowed on the VLAN. Querier
  • D-Link DXS-1100-10TS | User Manual - Page 81
    D-Link 10 Gigabit Ethernet Switch User Manual L2 Features > L2 Multicast Control> MLD Snooping > MLD Snooping Mrouter Settings This window is used to configure the specified interface(s) as the router ports or forbidden to be IPv6 multicast router ports on the VLAN interface on the Switch
  • D-Link DXS-1100-10TS | User Manual - Page 82
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual From Port / To Port: Select the appropriate port range used for the configuration here. This is available when Port is selected in the Statistics list.
  • D-Link DXS-1100-10TS | User Manual - Page 83
    10 Gigabit Ethernet Switch User Manual L2 Features > LLDP > LLDP Global Settings LLDP (Link Layer Discovery Protocol) provides IEEE 802.1AB standards-based method for switches to advertise themselves to neighbor devices, as well as to learn about neighbor LLDP devices. SNMP utilities can learn the
  • D-Link DXS-1100-10TS | User Manual - Page 84
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.107 - L2 Features > LLDP > LLDP Port Settings The fields that can be configured are described below: From Port / To Port: Select the appropriate port
  • D-Link DXS-1100-10TS | User Manual - Page 85
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are to enable the settings for the Basic TLVs Settings. An active LLDP port on the Switch always included mandatory data in its outbound advertisements. There are four optional data types that can
  • D-Link DXS-1100-10TS | User Manual - Page 86
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.110 - L2 Features > LLDP > LLDP Dot1 TLVs Settings The fields that can be configured are described below: From Port / To Port: Select the appropriate
  • D-Link DXS-1100-10TS | User Manual - Page 87
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.111 - L2 Features > LLDP > LLDP Dot3 TLVs Settings The fields that can be configured are described below: From Port / To Port: Select the appropriate
  • D-Link DXS-1100-10TS | User Manual - Page 88
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.112 - L2 Features > LLDP > LLDP-MED Port Settings The fields that can be configured are described below: is used to view the neighbor detection activity, LLDP Statistics and the settings for individual ports on the Switch. 81
  • D-Link DXS-1100-10TS | User Manual - Page 89
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.113 - L2 Features > LLDP > LLDP Statistics Information The fields that can be configured are described below: Port: Select the port number that will be
  • D-Link DXS-1100-10TS | User Manual - Page 90
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.114 - L2 Features > LLDP > LLDP Local Port Information The fields that can be configured are described below: Port: Select the port number that will
  • D-Link DXS-1100-10TS | User Manual - Page 91
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.116 - L2 Features > LLDP > LLDP Local Port Information (Show Detail) L2 Features > LLDP > LLDP Neighbor Port Information This window is used to display the information learned from the neighbors. The switch receives packets
  • D-Link DXS-1100-10TS | User Manual - Page 92
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Get IP From: Select the get IP from option here. Options to choose from are Static, DHCP, and BOOTP. When the Static option is selected, users can enter the IPv4 address of this interface manually in the fields provided. When the DHCP
  • D-Link DXS-1100-10TS | User Manual - Page 93
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Apply to accept the changes made for each individual section. After clicking the Interface IPv6 Address tab, the following page will appear. Figure 4.121 -
  • D-Link DXS-1100-10TS | User Manual - Page 94
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Clear All to clear all the information in this table. Click Delete to remove the specific entry. Enter a page number and click Go to
  • D-Link DXS-1100-10TS | User Manual - Page 95
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.126 - QoS > Basic Settings > Port the packet in the next lower CoS queue will be serviced. When the weight of a CoS queue reaches zero, the queue will not be serviced until its weight is replenished. When weights of all
  • D-Link DXS-1100-10TS | User Manual - Page 96
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.127 - QoS > Basic Settings > Queue priority scheduling. So the weight of the last queue should be zero while the Differentiate Service is supported. Click Apply to accept the changes made. QoS > Basic Settings > CoS to Queue
  • D-Link DXS-1100-10TS | User Manual - Page 97
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described below: Queue ID: Select the queue ID that will be mapped to the corresponding CoS value. Options
  • D-Link DXS-1100-10TS | User Manual - Page 98
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.130 - QoS > Advanced Settings > Port Trust State The fields that can be configured are described below: From Port / To Port: Select the appropriate port
  • D-Link DXS-1100-10TS | User Manual - Page 99
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.131 - QoS > Advanced Settings > DSCP CoS Mapping computers (with source MAC addresses) unknown to the Switch prior to locking the port (or ports) from connecting to the Switch's locked ports and gaining access to the network.
  • D-Link DXS-1100-10TS | User Manual - Page 100
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Trap State: Enable or disable port security traps on the Switch. Trap Rate: Enter - All learned MAC addresses will not be purged out unless the user manually deletes those entries. Delete-on-Timeout - All learned MAC addresses will be
  • D-Link DXS-1100-10TS | User Manual - Page 101
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Aging Type: Select the aging type here. here. Tick Permanent so that all learned MAC address will not be purged out unless the user manually deletes those entries. VID: Enter the VLAN ID here. This value must be between 1 and 4094
  • D-Link DXS-1100-10TS | User Manual - Page 102
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described problem, the Safeguard Engine function was added to the Switch's software. The Safeguard Engine can help the overall operability of the Switch by minimizing the workload of the Switch
  • D-Link DXS-1100-10TS | User Manual - Page 103
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The traffic segmentation member list can be comprised of different interface types, for example port and port-channel in the same forwarding domain. If the
  • D-Link DXS-1100-10TS | User Manual - Page 104
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described below: Trap State: This window is used to view and configure the Denial-of-Service (DoS) attack prevention settings. The following well-known DoS types which can be detected by most
  • D-Link DXS-1100-10TS | User Manual - Page 105
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual • Land Attack: This type of attack involves IP packets where the source and destination address are set to the address of the target device. It
  • D-Link DXS-1100-10TS | User Manual - Page 106
    D-Link 10 Gigabit Ethernet Switch User Manual function. The Switch supports SSLv3. Other versions of SSL may not be compatible with this Switch and may cause problems upon authentication 's global status here. Service Policy: Enter the service policy name here. This name can be up to 32
  • D-Link DXS-1100-10TS | User Manual - Page 107
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual File Select: Select the file type that will be loaded here. Options to choose . Click Delete to remove a new entry based on the information entered. Security > SSL > SSL Service Policy This window is used to view and configure the SSL
  • D-Link DXS-1100-10TS | User Manual - Page 108
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.143 - Security > SSL > SSL Service Policy The fields that can be configured are described below: Policy Name: Enter the SSL service policy name here. This name can be up to 32 characters long. Session Cache Timeout: Enter the
  • D-Link DXS-1100-10TS | User Manual - Page 109
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual From Port / To Port: Select the appropriate port range used for the configuration here. Click Test to test the specific port. Click Clear All to
  • D-Link DXS-1100-10TS | User Manual - Page 110
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.146 - Monitoring > Statistics > Port The fields that can be configured are described below: From Port / To Port: Select the appropriate port range used for
  • D-Link DXS-1100-10TS | User Manual - Page 111
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.147 - Monitoring > Statistics > Port Detail Click Back to return to the previous window. Click Refresh to refresh the display table. Monitoring > Statistics > Port Counters
  • D-Link DXS-1100-10TS | User Manual - Page 112
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.148 - Monitoring > Statistics > Port Counters The fields that can be configured are described below: From Port / To Port: Select the appropriate port range used
  • D-Link DXS-1100-10TS | User Manual - Page 113
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Click Back to return to the previous window. Click Refresh to refresh the display table. Monitoring > Statistics > Counters This window is used to display all
  • D-Link DXS-1100-10TS | User Manual - Page 114
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.151 - Monitoring > Statistics > Port Counters Detail Click Back to return to passing through the first port. This is useful for network monitoring and troubleshooting purposes. Figure 4.152 - Monitoring > Mirror Settings 107
  • D-Link DXS-1100-10TS | User Manual - Page 115
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described drop-down list select the Port option. In the second drop-down list select the destination switch's port number. Source: Tick the checkbox, next to the Source option, to configure the
  • D-Link DXS-1100-10TS | User Manual - Page 116
    Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.155 - Green > Power Saving (Power Saving Global Settings) The fields that can be configured are described below: Link Detection Power Saving: Enable or disable the link detection state. When enabled, a port which has a link down
  • D-Link DXS-1100-10TS | User Manual - Page 117
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.156 - Green > Power Saving (Power Saving Shutdown Settings) The fields that can be defined in IEEE 802.3az. It is designed to reduce the energy consumption of a link when no packets are being sent. Figure 4.157 - Green > EEE 110
  • D-Link DXS-1100-10TS | User Manual - Page 118
    4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual The fields that can be configured are described below: From Port / To Port: Select the appropriate port range used for the configuration here. State: Enable
  • D-Link DXS-1100-10TS | User Manual - Page 119
    Specifications D-Link 10 Gigabit Ethernet Switch User Manual Appendix A - Technical Specifications Hardware Specifications Key Components / Performance Switching Capacity: - DXS-1100-10TS: 200 Gbps - DXS-1100-16TC: 320 Gbps Max. Forwarding Rate - DXS-1100-10TS: 148.801 Mpps - DXS-1100-16TC
  • D-Link DXS-1100-10TS | User Manual - Page 120
    .1D Spanning Tree (STP) 802.1w Rapid Spanning Tree (RSTP) Loopback detection 802.1AX/802.3ad link aggregation: - DXS-1100-10TS: Supports maximum of 5 groups per device and 4 ports per group - DXS-1100-16TC: Supports maximum of 8 groups per device and 8 ports per group Port mirroring LLDP/LLDP-MED L2
  • D-Link DXS-1100-10TS | User Manual - Page 121
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121