D-Link DXS-1100-10TS User Manual - Page 84

L2 Features > LLDP > LLDP Management Address List, IP Subtype

Get D-Link DXS-1100-10TS PDF manuals and user guides View all D-Link DXS-1100-10TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.107 - L2 Features > LLDP > LLDP Port Settings The fields that can be configured are described below: From Port / To Port: Select the appropriate port range used for the configuration here. Subtype: Select the subtype of LLDP TLV(s). Options to choose from are MAC Address and Local. Admin State: Select the local LLDP agent and allow it to send and receive LLDP frames on the port. Options to choose from are TX, RX, TX and RX, and Disabled. TX - The local LLDP agent can only transmit LLDP frames. RX - The local LLDP agent can only receive LLDP frames. TX and RX - The local LLDP agent can both transmit and receive LLDP frames. This is the default value. Disabled - The local LLDP agent can neither transmit nor receive LLDP frames. IP Subtype: Select the type of the IP address information to be sent. Options to choose from are Default, IPv4 and IPv6. Action: Enable or disable the action field. Address: Enter the IPv4 or IPv6 address that will be sent. Click Apply to accept the changes made. NOTE: The IPv4 or IPv6 address entered here should be an existing LLDP management IP address. L2 Features > LLDP > LLDP Management Address List This window is used to view the LLDP management address list. Figure 4.108 - L2 Features > LLDP > LLDP Management Address List 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
4 Configuration
D-Link 10 Gigabit Ethernet Switch User Manual
77
Figure 4.107 – L2 Features > LLDP > LLDP Port Settings
The fields that can be configured are described below:
From Port / To Port:
Select the appropriate port range used for the configuration here.
Subtype:
Select the subtype of LLDP TLV(s). Options to choose from are
MAC Address
and
Local
.
Admin State:
Select the local LLDP agent and allow it to send and receive LLDP frames on the port.
Options to choose from are
TX
,
RX
,
TX and RX
, and
Disabled
.
TX -
The local LLDP agent can only transmit LLDP frames.
RX -
The local LLDP agent can only receive LLDP frames.
TX and RX -
The local LLDP agent can both transmit and receive LLDP frames. This is the default
value.
Disabled -
The local LLDP agent can neither transmit nor receive LLDP frames.
IP Subtype:
Select the type of the IP address information to be sent. Options to choose from are
Default
,
IPv4
and
IPv6
.
Action:
Enable or disable the action field.
Address:
Enter the IPv4 or IPv6 address that will be sent.
Click
Apply
to accept the changes made.
NOTE:
The IPv4 or IPv6 address entered here
should be an existing LLDP management IP
address.
L2 Features > LLDP > LLDP Management Address List
This window is used to view the LLDP management address list.
Figure 4.108 – L2 Features > LLDP > LLDP Management Address List