D-Link DXS-1100-10TS User Manual - Page 87

L2 Features > LLDP > LLDP-MED Port Settings

Get D-Link DXS-1100-10TS PDF manuals and user guides View all D-Link DXS-1100-10TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual Figure 4.111 - L2 Features > LLDP > LLDP Dot3 TLVs Settings The fields that can be configured are described below: From Port / To Port: Select the appropriate port range used for the configuration here. MAC/PHY Configuration/Status: Enable or disable the MAC/PHY Configuration/Status TLV to send. The MAC/PHY Configuration/Status TLV is an optional TLV that identifies (1) the duplex and bit-rate capability of the sending IEEE 802.3 LAN node, and (2) the current duplex and bit-rate settings of the sending IEEE 802.3 LAN node. Link Aggregation: Enable or disable the Link Aggregation TLV to send. The Link Aggregation TLV indicates contains the following information. Whether the link is capable of being aggregated, whether the link is currently in an aggregation, and the aggregated port channel ID of the port. If the port is not aggregated, then the ID is 0. Maximum Frame Size: Enable or disable the Maximum Frame Size TLV to send. The Maximum Frame Size TLV indicates the maximum frame size capability of the implemented MAC and PHY. Click Apply to accept the changes made. L2 Features > LLDP > LLDP-MED Port Settings This window is used to enable or disable transmitting LLDP-MED TLVs. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
4 Configuration
D-Link 10 Gigabit Ethernet Switch User Manual
80
Figure 4.111 – L2 Features > LLDP > LLDP Dot3 TLVs Settings
The fields that can be configured are described below:
From Port / To Port:
Select the appropriate port range used for the configuration here.
MAC/PHY Configuration/Status:
Enable or disable the MAC/PHY Configuration/Status TLV to send. The
MAC/PHY Configuration/Status TLV is an optional TLV that identifies (1) the duplex and bit-rate capability of
the sending IEEE 802.3 LAN node, and (2) the current duplex and bit-rate settings of the sending IEEE
802.3 LAN node.
Link Aggregation:
Enable or disable the Link Aggregation TLV to send. The Link Aggregation TLV indicates
contains the following information. Whether the link is capable of being aggregated, whether the link is
currently in an aggregation, and the aggregated port channel ID of the port. If the port is not aggregated,
then the ID is 0.
Maximum Frame Size:
Enable or disable the Maximum Frame Size TLV to send. The Maximum Frame Size
TLV indicates the maximum frame size capability of the implemented MAC and PHY.
Click
Apply
to accept the changes made.
L2 Features > LLDP > LLDP-MED Port Settings
This window is used to enable or disable transmitting LLDP-MED TLVs.