D-Link DXS-1100-10TS User Manual - Page 75

L2 Features > L2 Multicast Control> IGMP Snooping > IGMP Snooping Groups Settings

Get D-Link DXS-1100-10TS PDF manuals and user guides View all D-Link DXS-1100-10TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

4 Configuration D-Link 10 Gigabit Ethernet Switch User Manual After clicking Modify or Edit in IGMP Snooping Settings window, the following window will appear. Figure 4.95 - L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping VLAN Settings The fields that can be configured are described below: Minimum Version: Select the minimum version of IGMP hosts that is allowed on the VLAN. Querier State: Enable or disable the querier state. Query Version: Select the general query packet version sent by the IGMP snooping querier. Options to choose from are 1, 2, and 3. Query Interval: Enter the interval at which the IGMP snooping querier sends IGMP general query messages periodically. Max Response Time: Enter the maximum response time, in seconds, advertised in IGMP snooping queries. The range is 1 to 25. Robustness Value: Enter the robustness variable used in IGMP snooping. Last Member Query Interval: Enter the interval at which the IGMP snooping querier sends IGMP groupspecific or group-source-specific (channel) query messages. Rate Limit: Enter the IGMP snooping rate limit used. Tick No Limit to ignore the rate limit. Click Apply to accept the changes made. Click the X button at the upper-right side to close the window. L2 Features > L2 Multicast Control> IGMP Snooping > IGMP Snooping Groups Settings This window is used to configure and view the IGMP snooping static group, and view IGMP snooping group. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
4 Configuration
D-Link 10 Gigabit Ethernet Switch User Manual
68
After clicking
Modify
or
Edit
in IGMP Snooping Settings window, the following window will appear.
Figure 4.95 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping VLAN Settings
The fields that can be configured are described below:
Minimum Version:
Select the minimum version of IGMP hosts that is allowed on the VLAN.
Querier State:
Enable or disable the querier state.
Query Version:
Select the general query packet version sent by the IGMP snooping querier. Options to
choose from are
1
,
2
, and
3
.
Query Interval:
Enter the interval at which the IGMP snooping querier sends IGMP general query messages
periodically.
Max Response Time:
Enter the maximum response time, in seconds, advertised in IGMP snooping queries.
The range is 1 to 25.
Robustness Value:
Enter the robustness variable used in IGMP snooping.
Last Member Query Interval:
Enter the interval at which the IGMP snooping querier sends IGMP group-
specific or group-source-specific (channel) query messages.
Rate Limit:
Enter the IGMP snooping rate limit used. Tick
No Limit
to ignore the rate limit.
Click
Apply
to accept the changes made.
Click the
X
button at the upper-right side to close the window.
L2 Features > L2 Multicast Control> IGMP Snooping > IGMP Snooping Groups Settings
This window is used to configure and view the IGMP snooping static group, and view IGMP snooping group.