Dell Inspiron 16 7610 Service Manual for computers with two fans - Page 19

Solid-state drive⁠—M.2 slot one, Removing the M.2 2230 solid-state drive

Get Dell Inspiron 16 7610 PDF manuals and user guides View all Dell Inspiron 16 7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Solid-state drive-M.2 slot one Removing the M.2 2230 solid-state drive Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed in M.2 slot one. NOTE: The M.2 card installed on M.2 slot one will depend on the configuration ordered. Supported card configurations on the M.2 card slot: ● M.2 2230 solid-state drive + M.2 2230 mounting bracket ● M.2 2280 solid-state drive The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the removal procedure. Steps 1. Remove the screw (M2x3) that secures the M.2 thermal shield to the system board. 2. Slide and lift the M.2 thermal shield off the system board. 3. Slide and lift the M.2 2230 solid-state drive off the system board. 4. Peel the M.2 2230 mounting bracket off the system board. NOTE: This step is only applicable when replacing the M.2 2230 solid-state drive with a M.2 2280 solid-state drive. Removing and installing components 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Solid-state drive—M.2 slot one
Removing the M.2 2230 solid-state drive
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
About this task
NOTE:
This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed in M.2 slot one.
NOTE:
The M.2 card installed on M.2 slot one will depend on the configuration ordered. Supported card configurations on
the M.2 card slot:
●
M.2 2230 solid-state drive + M.2 2230 mounting bracket
●
M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the
removal procedure.
Steps
1.
Remove the screw (M2x3) that secures the M.2 thermal shield to the system board.
2.
Slide and lift the M.2 thermal shield off the system board.
3.
Slide and lift the M.2 2230 solid-state drive off the system board.
4.
Peel the M.2 2230 mounting bracket off the system board.
NOTE:
This step is only applicable when replacing the M.2 2230 solid-state drive with a M.2 2280 solid-state drive.
Removing and installing components
19