Dell Inspiron 16 7610 Service Manual for computers with two fans - Page 35

Installing the I/O board

Get Dell Inspiron 16 7610 PDF manuals and user guides View all Dell Inspiron 16 7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Steps 1. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board. 2. Lift the power-button with fingerprint-reader cable-connector latch and disconnect the power-button with fingerprint- reader cable from the I/O board. NOTE: This step is only applicable for computers shipped with the optional fingerprint reader. 3. Lift the power-button board cable-connector latch and disconnect the power-button board cable from the I/O board. 4. Remove the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly. 5. Disconnect the coin-cell battery cable from the I/O board. 6. Lift the I/O board off the palm-rest and keyboard assembly. Installing the I/O board Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the I/O board and provides a visual representation of the installation procedure. Steps 1. Align the ports on the I/O board to the slots on the palm-rest and keyboard assembly. 2. Place the I/O board on the palm-rest and keyboard assembly. 3. Align the screw hole on the I/O board to the screw hole on the palm-rest and keyboard assembly. 4. Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly. 5. Connect the I/O-board cable to the connector on the I/O board and close the latch. Removing and installing components 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Steps
1.
Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board.
2.
Lift the power-button with fingerprint-reader cable-connector latch and disconnect the power-button with fingerprint-
reader cable from the I/O board.
NOTE:
This step is only applicable for computers shipped with the optional fingerprint reader.
3.
Lift the power-button board cable-connector latch and disconnect the power-button board cable from the I/O board.
4.
Remove the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.
5.
Disconnect the coin-cell battery cable from the I/O board.
6.
Lift the I/O board off the palm-rest and keyboard assembly.
Installing the I/O board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the I/O board and provides a visual representation of the installation procedure.
Steps
1.
Align the ports on the I/O board to the slots on the palm-rest and keyboard assembly.
2.
Place the I/O board on the palm-rest and keyboard assembly.
3.
Align the screw hole on the I/O board to the screw hole on the palm-rest and keyboard assembly.
4.
Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.
5.
Connect the I/O-board cable to the connector on the I/O board and close the latch.
Removing and installing components
35