Dell OptiPlex 7090 Tower Service Manual - Page 83

Next steps, M.2 2230 SSD

Get Dell OptiPlex 7090 Tower PDF manuals and user guides View all Dell OptiPlex 7090 Tower manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

4. Route the power cable through the routing guides on the chassis and connect the power cables to their respective connectors on the system board. 5. Align the front I/O-bracket with the slots on the chassis. 6. Replace the (#6-32) screw that secures the front I/O-bracket to the chassis. Next steps 1. Install the processor. 2. Install the chassis fan. 3. Install the processor fan and 125 W heat-sink assembly or processor fan and heat-sink assembly. 4. Install the coin-cell battery. 5. Install the VR heatsink. 6. Remove the intrusion switch. 7. Remove the speaker. 8. Install the powered GPU. NOTE: This step is required only if the system is configured with powered GPU. 9. Install the graphics card. 10. Install the M.2 2230 SSD/M.2 2280 SSD. 11. Install the WLAN. 12. Install the memory module. 13. Install the front bezel. 14. Install the side cover. 15. Follow the procedure in after working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board. Removing and installing components 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
4.
Route the power cable through the routing guides on the chassis and connect the power cables to their respective
connectors on the system board.
5.
Align the front I/O-bracket with the slots on the chassis.
6.
Replace the (#6-32) screw that secures the front I/O-bracket to the chassis.
Next steps
1.
Install the
processor
.
2.
Install the
chassis fan
.
3.
Install the
processor fan and 125 W heat-sink assembly
or
processor fan and heat-sink assembly
.
4.
Install the
coin-cell battery
.
5.
Install the
VR heatsink
.
6.
Remove the
intrusion switch
.
7.
Remove the
speaker
.
8.
Install the
powered GPU
.
NOTE:
This step is required only if the system is configured with powered GPU.
9.
Install the
graphics card
.
10.
Install the
M.2 2230 SSD
/
M.2 2280 SSD
.
11.
Install the
WLAN
.
12.
Install the
memory module
.
13.
Install the
front bezel
.
14.
Install the
side cover
.
15.
Follow the procedure in
after working inside your computer
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE:
Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup
program. You must make the appropriate changes again after you replace the system board.
Removing and installing components
83