Dell PowerEdge R900 Hardware Owner's Manual (PDF) - Page 29

E1A14 SAS Cable - firmware

Get Dell PowerEdge R900 PDF manuals and user guides View all Dell PowerEdge R900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Table 1-5. LCD Status Messages Code Test Causes Corrective Actions E1811 HDD ## Rbld Abrt The specified hard drive has experienced a rebuild abort. See "Troubleshooting a Hard Drive" on page 142. If the problem persists, see your RAID documentation. E1812 HDD ## Removed The specified hard drive Information only. has been removed from the system. E1913 CPU & Firmware Mismatch The BMC firmware does not support the processor. Update to the latest BMC firmware. See the BMC User's Guide for more information on setup and use of BMC. E1A14 SAS Cable A SAS cable A is missing or bad. Reseat the cable. If problem persists, replace cable. See "SAS Controller Card" on page 78. E1A15 SAS Cable B SAS cable B is missing or bad. Reseat the cable. If problem persists, replace cable. See "SAS Controller Card" on page 78. E2010 No Memory No memory is installed in the system. Install memory. See "General Memory Module Installation Guidelines" on page 92. E2011 Mem Config Error Memory detected, but is not configurable. Error detected during memory configuration. See "Troubleshooting System Memory" on page 139. E2012 Unusable Memory Memory is configured, but See "Troubleshooting not usable. Memory System Memory" on subsystem failure. page 139. E2013 Shadow BIOS The system BIOS failed to See "Troubleshooting Fail copy its flash image into System Memory" on memory. page 139. About Your System 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
About Your System
29
E1811 HDD ## Rbld
Abrt
The specified hard drive
has experienced a rebuild
abort.
See "Troubleshooting a
Hard Drive" on page 142. If
the problem persists, see
your RAID
documentation.
E1812 HDD ##
Removed
The specified hard drive
has been removed from the
system.
Information only.
E1913 CPU &
Firmware
Mismatch
The BMC firmware does
not support the processor.
Update to the latest BMC
firmware. See the
BMC
User’s Guide
for more
information on setup and
use of BMC.
E1A14 SAS Cable A
SAS cable A is missing or
bad.
Reseat the cable. If
problem persists, replace
cable. See "SAS Controller
Card" on page 78.
E1A15 SAS Cable B
SAS cable B is missing or
bad.
Reseat the cable. If
problem persists, replace
cable. See "SAS Controller
Card" on page 78.
E2010 No Memory
No memory is installed in
the system.
Install memory. See
"General Memory Module
Installation Guidelines" on
page 92.
E2011 Mem Config
Error
Memory detected, but is
not configurable. Error
detected during memory
configuration.
See "Troubleshooting
System Memory" on
page 139.
E2012 Unusable
Memory
Memory is configured, but
not usable. Memory
subsystem failure.
See "Troubleshooting
System Memory" on
page 139.
E2013 Shadow BIOS
Fail
The system BIOS failed to
copy its flash image into
memory.
See "Troubleshooting
System Memory" on
page 139.
Table 1-5.
LCD Status Messages
Code
Test
Causes
Corrective Actions