Dell S3048-ON Networking S3048–ON Getting Started Guide - Page 28

Dell Networking OS, interface vlan, tagged &lt, GigabitEthernet, port-channel, show vlan

Get Dell S3048-ON PDF manuals and user guides View all Dell S3048-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

interface vlan vlan-id 2 Enable an interface to include the IEEE 802.1Q tag header. INTERFACE mode tagged interface - Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. This command is available only in VLAN interfaces. 3 Move untagged interfaces. Access INTERFACE VLAN mode of the VLAN to which you want to assign the interface. CONFIGURATION mode interface vlan vlan-id 4 Configure an interface as untagged. INTERFACE mode untagged interface - Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. This command is available only in VLAN interfaces. 5 To exit Configuration mode, use the exit command. To view which interfaces are tagged or untagged and to view which VLAN the interfaces belong, use the show vlan command. To view just the interfaces that Dell Networking OS 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
interface vlan
vlan-id
2
Enable an interface to include the IEEE 802.1Q tag header.
INTERFACE mode
tagged <
interface type
>
interface
<
interface type
>
— Enter the following keywords and slot/port or number
information:
•
For a 1-Gigabit Ethernet interface, enter the keyword
GigabitEthernet
then the slot/port information.
•
For a Port Channel interface, enter the keywords
port-channel
then a
number. The range is from 1 to 128.
•
For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
then the slot/port information.
This command is available only in VLAN interfaces.
3
Move untagged interfaces.
Access INTERFACE VLAN mode of the VLAN to
which you want to assign the interface.
CONFIGURATION mode
interface vlan
vlan-id
4
Configure an interface as untagged.
INTERFACE mode
untagged <
interface type
>
interface
<
interface type
>
— Enter the following keywords and slot/port or number
information:
•
For a 1-Gigabit Ethernet interface, enter the keyword
GigabitEthernet
then the slot/port information.
•
For a Port Channel interface, enter the keywords
port-channel
then a
number. The range is from 1 to 128.
•
For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
then the slot/port information.
This command is available only in VLAN interfaces.
5
To exit Configuration mode, use the
exit
command.
To view which interfaces are tagged or untagged and to view which VLAN the
interfaces belong, use the
show vlan
command. To view just the interfaces that
Dell Networking OS
28