Home » Dell Manuals » Hubs & Switches » Dell S5232F-ON » Manual Viewer

Dell S5232F-ON EMC Networking OS10 Enterprise Edition Deployment Guide with Ci - Page 16

OS10EE Deployment Guide - Cisco, APIC configuration steps

Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

APIC configuration steps that are used in the validated environment are provided in the attachment titled OS10EE Deployment Guide - Cisco APIC configuration steps. See the Cisco ACI documentation for detailed APIC configuration instructions. Note: In this environment, the 100 GbE ports on the ACI leaf switches are used as downlinks to the S5248FON switches. By default, the 100 GbE switch ports are designated for fabric connections, such as connections to ACI spine switches. To use these 100 GbE switch ports for connecting to devices outside of the ACI fabric, they must be configured as downlinks. Refer to Cisco documentation for more information. 16 Dell EMC Networking OS10 Enterprise Edition Deployment Guide with Cisco ACI

Section	Page
1 Introduction	5
1.1 Typographical conventions	5
1.2 Attachments	6
2 Hardware overview	7
2.1 Dell EMC Networking S5248F-ON	7
2.2 Dell EMC Networking S4148F-ON	7
2.3 Dell EMC Networking S3048-ON	7
2.4 Cisco Nexus C93180YC-EX	8
2.5 Cisco Nexus C9336-PQ	8
2.6 Supported Dell EMC switches	8
3 Cisco Application Centric Infrastructure (ACI)	9
4 Dell EMC ToR switches with Cisco ACI environment overview	10
4.1 Validated environment	11
5 OOB Management network	13
6 Cisco APIC configuration	15
7 Configure S5248F-ON switches	17
7.1 OOB management configuration	17
7.2 VLT configuration	17
7.3 Configure the VLANs	18
7.4 Server-facing configuration	19
7.5 Switch pair uplink configuration	20
8 vCenter configuration overview	21
9 Verify configuration	23
9.1 Validation using OS10EE CLI	23
9.1.1 show vlt [domain-id] command	23
9.1.2 show vlt [domain-id] vlt-port-detail command	24
9.1.3 show interface port channel summary command	24
9.1.4 show lldp neighbors command	24
9.1.5 show spanning-tree brief command	25
9.1.6 show uplink state group command	25
9.2 Cisco ACI validation	26
9.2.1 Verify vPC configuration	26
9.2.2 Verify physical interface configuration	28
9.2.3 Verify ACI is learning endpoints	29
9.3 Verify connectivity between VMs	30
A Additional information	31
A.1 Reset OS10EE switches to factory defaults	31
A.2 Spanning Tree Protocol recommendations	31
B Validated components	32
B.1 Dell EMC Networking switches	32
B.2 Cisco ACI components	32
C Technical resources	33

Match case Limit results 1 per page

Dell EMC Networking OS10 Enterprise Edition Deployment Guide with Cisco ACI

APIC configuration steps that are used in the validated environment are provided in the attachment titled

OS10EE Deployment Guide - Cisco

APIC configuration steps

. See the Cisco ACI documentation for

detailed APIC configuration instructions.

Note:

In this environment, the 100 GbE ports on the ACI leaf switches are used as downlinks to the S5248F-

ON switches. By default, the 100 GbE switch ports are designated for fabric connections, such as

connections to ACI spine switches. To use these 100 GbE switch ports for connecting to devices outside of

the ACI fabric, they must be configured as downlinks. Refer to Cisco documentation for more information.