Home » Dell Manuals » Hubs & Switches » Dell S5232F-ON » Manual Viewer

Dell S5232F-ON EMC Networking OS10 Enterprise Edition Deployment Guide with Ci - Page 30

Verify connectivity between VMs, OS10EE Deployment Guide, Cisco, APIC configuration steps

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

9.3 Verify connectivity between VMs In ACI, by default, communication flows freely within EPGs, but not between EPGs. To enable inter-EPG communication, contracts are configured on the APIC. This example is configured for unrestricted inter-EPG communication as shown in steps 17 through 19 in the attachment titled OS10EE Deployment Guide Cisco APIC configuration steps. Connectivity is verified by pinging between the VMs shown in Figure 6. Since inter-EPG communication is allowed using configured contracts, all VMs can ping all other VMs in the topology. Figure 17 shows that the VM named app-01, located in a rack server, successfully pinging the VMs named web-03 and db-04, which are on the servers. Verifying connectivity between VMs 30 Dell EMC Networking OS10 Enterprise Edition Deployment Guide with Cisco ACI

Section	Page
1 Introduction	5
1.1 Typographical conventions	5
1.2 Attachments	6
2 Hardware overview	7
2.1 Dell EMC Networking S5248F-ON	7
2.2 Dell EMC Networking S4148F-ON	7
2.3 Dell EMC Networking S3048-ON	7
2.4 Cisco Nexus C93180YC-EX	8
2.5 Cisco Nexus C9336-PQ	8
2.6 Supported Dell EMC switches	8
3 Cisco Application Centric Infrastructure (ACI)	9
4 Dell EMC ToR switches with Cisco ACI environment overview	10
4.1 Validated environment	11
5 OOB Management network	13
6 Cisco APIC configuration	15
7 Configure S5248F-ON switches	17
7.1 OOB management configuration	17
7.2 VLT configuration	17
7.3 Configure the VLANs	18
7.4 Server-facing configuration	19
7.5 Switch pair uplink configuration	20
8 vCenter configuration overview	21
9 Verify configuration	23
9.1 Validation using OS10EE CLI	23
9.1.1 show vlt [domain-id] command	23
9.1.2 show vlt [domain-id] vlt-port-detail command	24
9.1.3 show interface port channel summary command	24
9.1.4 show lldp neighbors command	24
9.1.5 show spanning-tree brief command	25
9.1.6 show uplink state group command	25
9.2 Cisco ACI validation	26
9.2.1 Verify vPC configuration	26
9.2.2 Verify physical interface configuration	28
9.2.3 Verify ACI is learning endpoints	29
9.3 Verify connectivity between VMs	30
A Additional information	31
A.1 Reset OS10EE switches to factory defaults	31
A.2 Spanning Tree Protocol recommendations	31
B Validated components	32
B.1 Dell EMC Networking switches	32
B.2 Cisco ACI components	32
C Technical resources	33

Match case Limit results 1 per page

Dell EMC Networking OS10 Enterprise Edition Deployment Guide with Cisco ACI

9.3

Verify connectivity between VMs

In ACI, by default, communication flows freely within EPGs, but not between EPGs. To enable inter-EPG

communication, contracts are configured on the APIC. This example is configured for unrestricted inter-EPG

communication as shown in steps 17 through 19 in the attachment titled

OS10EE Deployment Guide -

Cisco

APIC configuration steps

Connectivity is verified by pinging between the VMs shown in Figure 6. Since inter-EPG communication is

allowed using configured contracts, all VMs can ping all other VMs in the topology.

Figure 17 shows that the VM named app-01, located in a rack server, successfully pinging the VMs named

web-03 and db-04, which are on the servers.

Verifying connectivity between VMs