Dell Vostro 15 5510 Service Manual - Page 43

Installing the I/O board

Get Dell Vostro 15 5510 PDF manuals and user guides View all Dell Vostro 15 5510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Steps 1. Remove the three (M2.5x4.5) screws that secure the left hinge to the palm-rest and keyboard assembly. 2. Open the display hinge at an angle of 90 degrees. 3. Open the latch, and disconnect the power button with optional fingerprint reader cable from the I/O board. 4. Disconnect the coin-cell battery cable from the I/O board. 5. Peel the tape that secures the I/O-board cable to the I/O board. 6. Open the latch and disconnect the I/O-board cable from the I/O board. 7. Remove the screw (M2x2) that secures the I/O board to the palm-rest and keyboard assembly. 8. Lift the I/O board off the palm-rest and keyboard assembly. Installing the I/O board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the I/O board and provides a visual representation of the installation procedure. Removing and installing components 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Steps
1.
Remove the three (M2.5x4.5) screws that secure the left hinge to the palm-rest and keyboard assembly.
2.
Open the display hinge at an angle of 90 degrees.
3.
Open the latch, and disconnect the power button with optional fingerprint reader cable from the I/O board.
4.
Disconnect the coin-cell battery cable from the I/O board.
5.
Peel the tape that secures the I/O-board cable to the I/O board.
6.
Open the latch and disconnect the I/O-board cable from the I/O board.
7.
Remove the screw (M2x2) that secures the I/O board to the palm-rest and keyboard assembly.
8.
Lift the I/O board off the palm-rest and keyboard assembly.
Installing the I/O board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.
Removing and installing components
43