Epson Equity II User Manual - Page 9

How To Use This Manual, The Equity II comes with the MS-DOS operating system and - setup disk

Page 9 highlights

How To Use This Manual This user's guide explains how to set up and care for the Equity II. It also describes how to connect optional equipment and start using your system. Follow the instructions in Chapter 1 to set up your system. Chapter 2 describes how to turn on the Equity II and gives general operational procedures. Chapter 3 explains how disks and disk drives work and shows you how to use them. Chapter 4 describes how to install and remove option cards. If you encounter a problem, refer to Chapter 5 on troubleshooting. Appendix A presents the Equity II's hardware specifications and Appendix B is a glossary of important computer terms this manual uses. Refer to the glossary whenever you come across an unfamiliar word. You may even want to glance through it before you start reading this book. Although illustrations in this manual show the Equity II model with the internal hard disk, the setup and operational procedures apply to all configurations. You do not need to read everything in this book; some sections may describe a particular option or accessory you do not have. The Equity II comes with the MS"-DOS operating system and the GW™-BASIC programming language. If you have used MS-DOS before on another computer, you will find that it works the same way on the Equity II. However, be sure to refer to your Equity MS-DOS manual to learn about the new commands and special utility programs Epson has added. You may have bought other software as well. This manual tells you how to load software diskettes. To learn how to use a program or an operating system, refer to the software manual that comes with it.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79

How To Use This Manual
This user’s guide explains how to set up and care for the Equity II. It
also describes how to connect optional equipment and start using your
system.
Follow the instructions in Chapter
1
to set up your system. Chapter
2
describes how to turn on the Equity II and gives general operational
procedures. Chapter 3 explains how disks and disk drives work and
shows you how to use them. Chapter 4 describes how to install and
remove option cards. If you encounter a problem, refer to Chapter 5 on
troubleshooting.
Appendix A presents the Equity II’s hardware specifications and
Appendix B is a glossary of important computer terms this manual uses.
Refer to the glossary whenever you come across an unfamiliar word.
You may even want to glance through it before you start reading this
book.
Although illustrations in this manual show the Equity II model with
the internal hard disk, the setup and operational procedures apply to all
configurations. You do not need to read everything in this book; some
sections may describe a particular option or accessory you do not have.
The Equity II comes with the MS”-DOS operating system and the
GW™-BASIC programming language. If you have used MS-DOS before
on another computer, you will find that it works the same way on the
Equity II. However, be sure to refer to your Equity MS-DOS manual to
learn about the new commands and special utility programs Epson has
added.
You may have bought other software as well. This manual tells you
how to load software diskettes. To learn how to use a program or an
operating system, refer to the software manual that comes with it.