Epson LQ-510X User Manual - Page 189

cannot, sheet, ON LINE, the ON LINE, the LOAD/EJECT, Paper loads, but then jams.

Get Epson LQ-510X PDF manuals and user guides View all Epson LQ-510X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 189 highlights

l Paper loads, but then jams. The cut sheet feeder mode may be turned on (DIP switch 1-8 is on). When the cut sheet feeder is not in use, DIP switch 1-8 should be off. The edge guides may be too far apart. Adjust the edge guides to the width of the paper. The dimensions of the paper may exceed the specified limitations. Use only paper sizes that are within the specified range. Multi-part forms cannot be used with this printer's single sheet feeding system. Continuous paper does not feed properly. l When the LOAD/EJECT button is pressed, the platen does not rotate and paper does not feed. You may be trying to feed paper using the control panel buttons while the printer is on line (ON LINE light on). Press the ON LINE button once to set the printer off line; then try feeding paper. After feeding paper, press the ON LINE button again to set the printer on line. The paper release lever may be pushed back to the single sheet position. When using the tractor, be sure the paper release lever is pulled forward to the continuous paper position. On the wide carriage printer, the paper release lever must be in the center position when using the built-in push tractor, and it must be in the forward position when using the optional pull tractor. l When the LOAD/EJECT button is pressed, the platen rotates but paper does not feed. Continuous paper may have already been in the paper path. (In this case, the paper feeds backward to the standby position.) Press the LOAD/EJECT button again to load the paper. 7-8 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
l
Paper loads, but then jams.
The cut sheet feeder mode may be turned on (DIP switch 1-8 is
on). When the cut sheet feeder is not in use, DIP switch 1-8
should be off.
The edge guides may be too far apart. Adjust the edge guides to
the width of the paper.
The dimensions of
the
paper may exceed the specified
limitations. Use only paper sizes that are within the specified
range. Multi-part forms
cannot
be used with this printer’s single
sheet
feeding system.
Continuous paper does not feed properly.
l
When the
LOAD/EJECT
button is pressed, the platen does not rotate
and
paper does not feed.
You may be trying to feed paper using the control panel buttons
while the printer is on line
(ON LINE
light on). Press
the ON LINE
button once to set the printer off line; then try feeding paper.
After feeding paper, press the
ON LINE
button again to set the
printer on line.
The paper release lever may be pushed back to the single sheet
position. When using the tractor, be sure the paper release lever
is pulled forward to the continuous paper position.
On the wide carriage printer, the paper release lever must be in
the center position when using the built-in push tractor, and it
must be in the forward position
when
using the optional pull
tractor.
l
When the
LOAD/EJECT
button is pressed, the platen rotates but paper
does not
feed.
Continuous paper may
have
already been in the paper path. (In
this case, the paper feeds backward to the standby position.)
Press
the LOAD/EJECT
button again to load the paper.
7-8
Troubleshooting