Fluke 753 Fluke 750 Series User Manual - Page 14

Safety Information, sure that the Product operates correctly. - 754 manual

Get Fluke 753 PDF manuals and user guides View all Fluke 753 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

753/754 Users Manual Safety Information A Warning identifies conditions and actions that pose hazards to the user; a Caution identifies conditions and actions that may damage the Product or the equipment under test.  Warning To prevent personal injury, use the Product only as specified, or the protection supplied by the Product can be compromised. To prevent possible electrical shock, fire, or personal injury: • Read all safety Information before you use the Product. • Carefully read all instructions. • Use only correct measurement category (CAT), voltage, and amperage rated probes, test leads, and adapters for the measurement. • The battery must be locked in place before you operate the Product. • Recharge the battery when the low battery indicator shows to prevent incorrect measurements. • Do not apply more than the rated voltage, between the terminals or between each terminal and earth ground. 2 • Limit operation to the specified measurement category, voltage, or amperage ratings. • Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component of a Product, probe, or accessory. • Measure a known voltage first to make sure that the Product operates correctly. • Do not touch voltages > 30 V ac rms, 42 V ac peak, or 60 V dc. • Do not use the Product around explosive gas, vapor, or in damp or wet environments. • Do not use and disable the Product if it is damaged. • Do not use the Product if it operates incorrectly. • Keep fingers behind the finger guards on the probes. • Remove all probes, test leads, and accessories that are not necessary for the measurement. • Only use probes, test leads, and accessories that have the same measurement category, voltage, and amperage ratings as the Product.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
753/754
Users Manual
2
Safety Information
A
Warning
identifies conditions and actions that pose
hazards to the user; a
Caution
identifies conditions and
actions that may damage the Product or the equipment
under test.

Warning
To prevent personal injury, use the Product
only as specified, or the protection supplied by
the Product can be compromised.
To prevent possible electrical shock, fire, or
personal injury:
•
Read all safety Information before you use
the Product.
•
Carefully read all instructions.
•
Use only correct measurement category
(CAT), voltage, and amperage rated
probes, test leads, and adapters for the
measurement.
•
The battery must be locked in place before
you operate the Product.
•
Recharge the battery when the low battery
indicator shows to prevent incorrect
measurements.
•
Do not apply more than the rated voltage,
between the terminals or between each
terminal and earth ground.
•
Limit operation to the specified
measurement category, voltage, or
amperage ratings.
•
Do not exceed the Measurement Category
(CAT) rating of the lowest rated individual
component of a Product, probe, or
accessory.
•
Measure a known voltage first to make
sure that the Product operates correctly.
•
Do not touch voltages > 30 V ac rms, 42 V
ac peak, or 60 V dc.
•
Do not use the Product around explosive
gas, vapor, or in damp or wet
environments.
•
Do not use and disable the Product if it is
damaged.
•
Do not use the Product if it operates
incorrectly.
•
Keep fingers behind the finger guards on
the probes.
•
Remove all probes, test leads, and
accessories that are not necessary for the
measurement.
•
Only use probes, test leads, and
accessories that have the same
measurement category, voltage, and
amperage ratings as the Product.