Fluke 753 Fluke 750 Series User Manual - Page 40

Measure Mode, Measurement Ranges

Get Fluke 753 PDF manuals and user guides View all Fluke 753 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

753/754 Users Manual Figure 11. Personalize the Product gks40s.bmp 5. The ID string is shown at the bottom of the boxed area. To erase a character, push the Back Space softkey. To erase the complete string, push . Information recorded in the ID string is recorded with all measurements stored in memory. 6. Push or  to select a character, then push . Use the numeric keypad to record numbers. 7. Do step 6 until satisfied with the ID string. 8. Push the Done softkey. 9. Push the Done softkey or s to exit Setup mode. Measure Mode Note To get the best noise rejection and highest accuracy performance when you measure, use the battery; do not use the battery charger. The operation mode (for example, MEASURE, SOURCE) is shown in the top left of the display. If the Product is not in MEASURE mode, push  until MEASURE is shown. The Product must be in MEASURE mode to change the MEASURE parameters. Measurement Ranges The Product usually changes to the correct measurement range automatically. The lower left side of the display shows "Range" or "Auto" if on the range status. Auto Range switch points are shown in Specifications. When the Range softkey is pushed, the range is locked. Push it again to go to and lock on the next higher range. Auto Range is in operation when a different measurement function is selected. If the range is locked, overrange inputs show on the display as In Auto Range, out of range is shown as 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
753/754
Users Manual
28
gks40s.bmp
Figure 11. Personalize the Product
5.
The
ID
string is shown at the bottom of the boxed area.
To erase a character, push the
Back Space
softkey. To
erase the complete string, push
. Information
recorded in the ID string is recorded with all
measurements stored in memory.
6.
Push
,
,
, or
to select a character, then push
. Use the numeric keypad to record numbers.
7.
Do step 6 until satisfied with the ID string.
8.
Push the
Done
softkey.
9.
Push the
Done
softkey or
s
to exit Setup mode.
Measure Mode
Note
To get the best noise rejection and highest
accuracy performance when you measure, use the
battery; do not use the battery charger.
The operation mode (for example, MEASURE, SOURCE) is
shown in the top left of the display. If the Product is not in
MEASURE mode, push
until MEASURE is shown. The
Product must be in MEASURE mode to change the
MEASURE parameters.
Measurement Ranges
The Product usually changes to the correct measurement
range automatically. The lower left side of the display shows
“Range” or “Auto” if on the range status. Auto Range switch
points are shown in Specifications. When the
Range
softkey
is pushed, the range is locked. Push it again to go to and
lock on the next higher range. Auto Range is in operation
when a different measurement function is selected.
If the range is locked, overrange inputs show on the
display as
- - - - - -
. In Auto Range, out of range is
shown as
! ! ! ! ! !
.