Fluke TIS20-9Hz User Manual - Page 47

Battery Care, Connect the battery charger to the mains power

Get Fluke TIS20-9Hz PDF manuals and user guides View all Fluke TIS20-9Hz manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Battery Care  Warning To prevent personal injury and for safe operation of the Product: • Do not put battery cells and battery packs near heat or fire. Do not put in sunlight. • Do not disassemble or crush battery cells and battery packs. • Remove batteries to prevent battery leakage and damage to the Product if it is not used for an extended period. • Connect the battery charger to the mains power outlet before the Product or battery. • Use only Fluke approved power adapters to charge the battery. • Keep cells and battery packs clean and dry. Clean dirty connectors with a dry, clean cloth.  Caution To prevent damage, do not expose Product to heat sources or high-temperature environments such as an unattended vehicle in the sun. Performance Series Thermal Imagers Maintenance To get the best performance from the lithium-ion battery: • Do not store the battery on the charger for more than 24 hours. • Charge the Imager for a two-hour minimum at threemonth intervals for maximum battery life. • The battery will discharge in about three months if installed in the Imager and powered off. It will discharge in about six months if stored disconnected from the Imager. • Batteries stored for long periods will need two to ten charging cycles for full capacity. • Always operate in the specified temperature range. • Do not store the batteries in extreme cold environments. • Do not attempt to charge the batteries in extreme cold environments. • These guidelines apply whether you charge the battery with external power or the charger base.   Caution Do not incinerate the Product and/or battery. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Performance Series Thermal Imagers
Maintenance
37
Battery Care
Warning
To prevent personal injury and for safe operation
of the Product:
•
Do not put battery cells and battery packs near
heat or fire. Do not put in sunlight.
•
Do not disassemble or crush battery cells and
battery packs.
•
Remove batteries to prevent battery leakage
and damage to the Product if it is not used for
an extended period.
•
Connect the battery charger to the mains power
outlet before the Product or battery.
•
Use only Fluke approved power adapters to
charge the battery.
•
Keep cells and battery packs clean and dry.
Clean dirty connectors with a dry, clean cloth.
Caution
To prevent damage, do not expose Product to
heat sources or high-temperature
environments such as an unattended vehicle
in the sun.
To get the best performance from the lithium-ion battery:
•
Do not store the battery on the charger for more than
24 hours.
•
Charge the Imager for a two-hour minimum at three-
month intervals for maximum battery life.
•
The battery will discharge in about three months if
installed in the Imager and powered off. It will
discharge in about six months if stored disconnected
from the Imager.
•
Batteries stored for long periods will need two to ten
charging cycles for full capacity.
•
Always operate in the specified temperature range.
•
Do not store the batteries in extreme cold
environments.
•
Do not attempt to charge the batteries in extreme cold
environments.
•
These guidelines apply whether you charge the battery
with external power or the charger base.
Caution
Do not incinerate the Product and/or battery.