HP 4000 Maintenance & Service Guide HP Compaq 4000 Pro Small Form Factor B - Page 58

Channel A and Channel B. Refer to, Rotating the Drive Cage Down

Get HP 4000 - SureStore DLT 40e Tape Drive PDF manuals and user guides View all HP 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

4. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 6-7 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. A DIMM must occupy the black XMM1 socket. For maximum performance, populate the sockets so that the memory capacity is equal between Channel A and Channel B. Refer to Populating DIMM Sockets on page 46 for more information. 5. Push the module down into the socket, ensuring that the module is fully inserted and properly seated. Make sure the latches are in the closed position (3). 6. Rotate the drive cage back down to its normal position. Figure 6-8 Rotating the Drive Cage Down 7. Replace the access panel. 8. If the computer was on a stand, replace the stand. 48 Chapter 6 Removal and Replacement Procedures Small Form Factor (SFF) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
4.
Open both latches of the memory module socket
(1)
, and insert the memory module into the
socket
(2)
.
Figure 6-7
Installing a DIMM
NOTE:
A memory module can be installed in only one way. Match the notch on the module
with the tab on the memory socket.
A DIMM must occupy the black XMM1 socket.
For maximum performance, populate the sockets so that the memory capacity is equal between
Channel A and Channel B. Refer to
Populating DIMM Sockets
on page
46
for more information.
5.
Push the module down into the socket, ensuring that the module is fully inserted and properly
seated. Make sure the latches are in the closed position (3).
6.
Rotate the drive cage back down to its normal position.
Figure 6-8
Rotating the Drive Cage Down
7.
Replace the access panel.
8.
If the computer was on a stand, replace the stand.
48
Chapter 6
Removal and Replacement Procedures Small Form Factor (SFF) Chassis