HP 4000 Maintenance & Service Guide HP Compaq 4000 Pro Small Form Factor B - Page 85

Speaker, Preparation for Disassembly, on Computer Access Panel, Front Bezel

Get HP 4000 - SureStore DLT 40e Tape Drive PDF manuals and user guides View all HP 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

8. Route the cables through the slots beneath the drive cage, pull the assembly (right side first) into the chassis, and then remove the assembly from the computer. Figure 6-46 Routing the cables and removing the power switch assembly To install the front I/O and power switch assembly, reverse the removal procedure. NOTE: Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly. Proper cable routing prevents damage to the cables and allows the drive cage to close properly. Speaker Description Speaker Spare part number 636925-001 The speaker is attached to the front of the chassis under the rotating drive cage. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 40). 2. Remove the access panel (Computer Access Panel on page 41). 3. Remove the front bezel (Front Bezel on page 42). 4. Rotate the drive cage to its upright position. 5. Disconnect the speaker wire from the white system board labeled SPKR 6. Remove the two screws that secure the speaker to the chassis (1). Speaker 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
8.
Route the cables through the slots beneath the drive cage, pull the assembly (right side first) into
the chassis, and then remove the assembly from the computer.
Figure 6-46
Routing the cables and removing the power switch assembly
To install the front I/O and power switch assembly, reverse the removal procedure.
NOTE:
Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly.
Proper cable routing prevents damage to the cables and allows the drive cage to close properly.
Speaker
Description
Spare part number
Speaker
636925-001
The speaker is attached to the front of the chassis under the rotating drive cage.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
40
).
2.
Remove the access panel (
Computer Access Panel
on page
41
).
3.
Remove the front bezel (
Front Bezel
on page
42
).
4.
Rotate the drive cage to its upright position.
5.
Disconnect the speaker wire from the white system board labeled SPKR
6.
Remove the two screws that secure the speaker to the chassis
(1)
.
Speaker
75