HP 4000 Maintenance & Service Guide HP Compaq 4000 Pro Small Form Factor B - Page 76

CAUTION, Installing a Drive into the 3.5-inch Drive Bay Media Card Reader Shown

Get HP 4000 - SureStore DLT 40e Tape Drive PDF manuals and user guides View all HP 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

3. Install three M3 metric mounting screws in the lower holes on each side of the drive: two on the right side and one on the front left side. HP has provided extra M3 metric mounting screws on the front of the chassis, under the front bezel. The M3 metric mounting screws are black. Refer to Installing and Removing Drives on page 57 for an illustration of the extra M3 metric mounting screws location. CAUTION: Use only 5-mm long screws as mounting screws. Longer screws can damage the internal components of the drive. NOTE: When replacing the drive, transfer the three M3 metric mounting screws from the old drive to the new one. Figure 6-31 Installing Mounting Screws in the Media Card Reader 4. Position the mounting screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it stops. Figure 6-32 Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown) 66 Chapter 6 Removal and Replacement Procedures Small Form Factor (SFF) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
3.
Install three M3 metric mounting screws in the lower holes on each side of the drive: two on the
right side and one on the front left side. HP has provided extra M3 metric mounting screws on
the front of the chassis, under the front bezel. The M3 metric mounting screws are black. Refer
to
Installing and Removing Drives
on page
57
for an illustration of the extra M3 metric mounting
screws location.
CAUTION:
Use only 5-mm long screws as mounting screws. Longer screws can damage the
internal components of the drive.
NOTE:
When replacing the drive, transfer the three M3 metric mounting screws from the old
drive to the new one.
Figure 6-31
Installing Mounting Screws in the Media Card Reader
4.
Position the mounting screws on the drive into the J-slots in the drive bay. Then slide the drive
toward the front of the computer until it stops.
Figure 6-32
Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown)
66
Chapter 6
Removal and Replacement Procedures Small Form Factor (SFF) Chassis