HP Brocade 8/12c HP StorageWorks B-series Data Center Fabric Manager Professio - Page 8

EX_Port disabled when configuring Routing Domain IDs, FCIP/GigE Performance Graphs

Get HP Brocade 8/12c PDF manuals and user guides View all HP Brocade 8/12c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Tunnel ports shown instead of GigE ports In the topology view, tunnel ports are shown instead of Gigabit Ethernet ports. Deleting Logical Switches with GigE ports causes errors When deleting a Logical Switch that has Gigabit Ethernet ports without first moving the GigE ports to the default Logical Switch, an error message may be displayed and the delete fails. Blank graph displayed for FCIP tunnels When FCIP tunnels are selected from the Picker dialog in the Historical Graph, the tunnels will initially appear as blank until the Apply button in the dialog is clicked. Domain port index and port WWNs unavailable in Add Member dialog The port index and port WWNs are grayed out when using the Add Member dialog. The port index can still be selected by choosing the appropriate devices in the device tree and then moving them to the right. Event-based file actions fail DCFM event actions fails to run scripts on Windows remote-mounted filesystems. EX_Port disabled when configuring Routing Domain IDs After selecting an edge fabric and launching the routing domain IDs dialog, if you select all of the front domains and Xlate domains and then add appropriate domain IDs, clicking OK disables the EX_Ports with the following message: EX_PORT ISOLATE Incorrect title of Top Talkers dialog When the Top Talkers dialog is selected, the title incorrectly displays as "Realtime Port Selector." WWNs not shown in Fabric Binding dialog After two FOS fabrics in interop mode 0 are merged, the member's WWN is missing and the Fabric Binding Status is listed as Unknown in the Fabric Binding dialog. SNMP trap registration If the discovery status displays the message Not registered for SNMP Trap, manually add the server IP entry in the SNMP trap registration table from the switch CLI using the following command: snmpconfig --set snmpv3 FCIP/GigE Performance Graphs If there are no FCIP/GigE performance graphs shown for a switch, verify that the server IP address is properly registered in the SNMP trap registration table. To verify the IP address, enter the CLI command snmpconfig --show snmpv3 and verify that the SNMPv3 credentials exactly match the SNMPv3 user that the DCFM server is registered with for traps. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Tunnel ports shown instead of GigE ports
In the topology view, tunnel ports are shown instead of Gigabit Ethernet ports.
Deleting Logical Switches with GigE ports causes errors
When deleting a Logical Switch that has Gigabit Ethernet ports without first moving the GigE ports
to the default Logical Switch, an error message may be displayed and the delete fails.
Blank graph displayed for FCIP tunnels
When FCIP tunnels are selected from the Picker dialog in the Historical Graph, the tunnels will initially
appear as blank until the Apply button in the dialog is clicked.
Domain port index and port WWNs unavailable in Add Member dialog
The port index and port WWNs are grayed out when using the Add Member dialog. The port index
can still be selected by choosing the appropriate devices in the device tree and then moving them to
the right.
Event-based file actions fail
DCFM event actions fails to run scripts on Windows remote-mounted filesystems.
EX_Port disabled when configuring Routing Domain IDs
After selecting an edge fabric and launching the routing domain IDs dialog, if you select all of the
front domains and Xlate domains and then add appropriate domain IDs, clicking OK disables the
EX_Ports with the following message:
EX_PORT ISOLATE
Incorrect title of Top Talkers dialog
When the Top Talkers dialog is selected, the title incorrectly displays as “Realtime Port Selector.”
WWNs not shown in Fabric Binding dialog
After two FOS fabrics in interop mode 0 are merged, the member's WWN is missing and the Fabric
Binding Status is listed as
Unknown
in the Fabric Binding dialog.
SNMP trap registration
If the discovery status displays the message
Not registered for SNMP Trap
, manually add
the server IP entry in the SNMP trap registration table from the switch CLI using the following command:
snmpconfig --set snmpv3
FCIP/GigE Performance Graphs
If there are no FCIP/GigE performance graphs shown for a switch, verify that the server IP address
is properly registered in the SNMP trap registration table. To verify the IP address, enter the CLI
command
snmpconfig --show snmpv3
and verify that the SNMPv3 credentials exactly match
the SNMPv3 user that the DCFM server is registered with for traps.
8