HP Carrier-grade cc3300 UserÆs Guide and Technical UserÆs Gu - Page 42

Configuration Software and Utilities

Get HP Carrier-grade cc3300 PDF manuals and user guides View all HP Carrier-grade cc3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

3 Configuration Software and Utilities This chapter describes the Power-On Self Test (POST) and server configuration utilities. The table below briefly describes the utilities. Table 14. Configuration Utilities Utility Description and brief procedure BIOS Setup If the system does not have a diskette drive, or the drive is disabled or incorrectly configured, use Setup to enable it. Or, you can move the CMOS jumper on the server board from the default setting (Protect CMOS memory) to the Clear setting; this will allow most server configurations to boot. Then run the SSU to configure the server. System Setup Utility (SSU) Use for viewing and clearing the system event log, viewing the system management FRU information, or viewing the system management SDR repository. FRU/SDR Load Utility Use to update the Field Replacement Unit (FRU), Sensor Data Record (SDR), and SM BIOS (SMB) flash components. BIOS Upgrade Utility Use to upgrade the BIOS. Firmware Update Utility Use to update the Firmware. Using the Adaptec SCSI Utility Use to configure or view the settings of the SCSI host adapter and onboard SCSI devices in the server. Configuration Software and Utilities 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Configuration Software and Utilities
42
3 Configuration Software and Utilities
This chapter describes the Power-On Self Test (POST) and server configuration utilities.
The table
below briefly describes the utilities.
Table 14.
Configuration Utilities
Utility
Description and brief procedure
BIOS Setup
If the system does not have a diskette drive, or the drive is
disabled or incorrectly configured, use Setup to enable it.
Or, you can move the CMOS jumper on the server board from the
default setting (Protect CMOS memory) to the Clear setting; this
will allow most server configurations to boot.
Then run the SSU to
configure the server.
System Setup Utility
(SSU)
Use for viewing and clearing the system event log, viewing the
system management FRU information, or viewing the system
management SDR repository.
FRU/SDR Load Utility
Use to update the Field Replacement Unit (FRU), Sensor Data
Record (SDR), and SM BIOS (SMB) flash components.
BIOS Upgrade Utility
Use to upgrade the BIOS.
Firmware Update Utility
Use to update the Firmware.
Using the Adaptec SCSI
Utility
Use to configure or view the settings of the SCSI host adapter and
onboard SCSI devices in the server.