HP ENVY 15-3033cl HP ENVY 15 - Maintenance and Service Guide - Page 65

Remove the Phillips PM2.0×2.8 screw, base enclosure.

Get HP ENVY 15-3033cl PDF manuals and user guides View all HP ENVY 15-3033cl manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

3. Release the wireless audio module antenna cables (1) and the wireless antenna cables (2) from the clips and routing channels built into the base enclosure. 4. Turn the computer right side up, with the front toward you. 5. Open the computer as far as it will open. 6. Disconnect the following cables from the system board: (1) Display proximity sensor cable (2) Display panel cable (3) Bluetooth module cable (only on computer models equipped with a Bluetooth module) 7. Release the wireless antenna cables (4) from the openings in the system board and base enclosure. 8. Remove the Phillips PM2.0×2.8 screw (1) and the Phillips PM2.5×4.9 screw (2) that secure the power connector bracket and power connector to the base enclosure. 9. Remove the power connector bracket (3). ENWW Component replacement procedures 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
3.
Release the wireless audio module antenna cables
(1)
and the wireless antenna cables
(2)
from
the clips and routing channels built into the base enclosure.
4.
Turn the computer right side up, with the front toward you.
5.
Open the computer as far as it will open.
6.
Disconnect the following cables from the system board:
(1)
Display proximity sensor cable
(2)
Display panel cable
(3)
Bluetooth module cable (only on computer models equipped with a Bluetooth module)
7.
Release the wireless antenna cables
(4)
from the openings in the system board and
base enclosure.
8.
Remove the Phillips PM2.0×2.8 screw
(1)
and the Phillips PM2.5×4.9 screw
(2)
that secure the
power connector bracket and power connector to the base enclosure.
9.
Remove the power connector bracket
(3)
.
ENWW
Component replacement procedures
57