HP Indigo WS6600 Dripping Prevention and ITM Heating Hood Service -- CA393-101 - Page 28

Route the second branch of the, connect the other end

Get HP Indigo WS6600 PDF manuals and user guides View all HP Indigo WS6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

12. When the IHH heater wiring is connected, check to make sure that no wiring touches the IHH blower. 1 W2227 2 W2228 13. For presses with external IHH: Connect cable W2230 to the IHH J4 connector (9 pin D type). Route the cable up to the top of the PE wall, and along the top of the wall to the left, to reach the MCN board. For presses without external IHH: the blower is connected to the PDB by cable W2223 form J10 on the PDB to the Amatek blower. For presses with external IHH: Remove the existing connector from J5 in the MCN board, and connect the other end of W2230 to J5. 14. Route the second branch of the W2230 cable down the inside right side of the exit side door frame, to the base of the PE chassis. Wrap the W2230 connector with tape and secure the cable using tie warps. The second branch of the W2230 connector is not used. Wiring the dripping prevention kit 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
12.
When the IHH heater wiring is connected, check to make sure that no wiring touches the IHH
blower.
1
W2227
2
W2228
13.
For presses with external IHH:
Connect cable
W2230
to the
IHH J4
connector (9 pin D type).
Route the cable up to the top of the PE wall, and along the top of the wall to the left, to reach the
MCN
board.
For presses without external IHH:
the blower is connected to the PDB by cable W2223 form J10 on
the PDB to the Amatek blower.
For presses with external IHH:
Remove the existing connector from
J5
in the MCN board, and
connect the other end of
W2230
to
J5
.
14.
Route the second branch of the
W2230
cable down the inside right side of the exit side door frame,
to the base of the PE chassis.
Wrap the
W2230
connector with tape and secure the cable using tie warps. The second branch of
the
W2230
connector is not used.
Wiring the dripping prevention kit
25