HP Indigo WS6600 Dripping Prevention and ITM Heating Hood Service -- CA393-101 - Page 52

Calibration Procedures > Imaging Oil Flow > Cleaning Station Flow Calibration Wizard

Get HP Indigo WS6600 PDF manuals and user guides View all HP Indigo WS6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Figure 3-24 ITM hood - Check isolation material 19. Turn on the press. 20. In the SysTab editior, check if the cleaning station pump voltage value is above 2500 (imgingoiltopic > imoCleanstationCtrlVoltage > IO_clean_station_control_voltage), and that the Cleaning Station Flow Calibration wizard did not succeed to reduce the flow to give a voltage value of approximately 2300. If this is so, the following components may be clogged: ● Cleaning station heat exchanger ● Cleaning station pump NOTE: For presses with the DFS installed - if the pump voltage value is near 2700, the DFS Automatic Calibration wizard may fail. 21. Run the Cleaning Station Flow Calibration wizard. Select Print Care > Maintenance > Subsystem Calibration Procedures > Imaging Oil Flow > Cleaning Station Flow Calibration Wizard. NOTE: For tips on how to get the most out of the wizard, refer to Calibrating cleaning station imaging oil flow (CA393-04840). If the wizard does not work, perform manual Cleaning Station Flow Calibration: NOTE: Two people are needed for this task a. Verify that the press is in Standby. b. Verify that the PIP drum is disengaged. Press in Shutdown 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Figure 3-24
ITM hood — Check isolation material
19.
Turn on the press.
20.
In the SysTab editior, check if the cleaning station pump voltage value is above 2500 (
imgingoiltopic
> imoCleanstationCtrlVoltage > IO_clean_station_control_voltage
), and that the Cleaning Station
Flow Calibration wizard did not succeed to reduce the flow to give a voltage value of approximately
2300. If this is so, the following components may be clogged:
●
Cleaning station heat exchanger
●
Cleaning station pump
NOTE:
For presses with the DFS installed — if the pump voltage value is near 2700, the DFS
Automatic Calibration wizard may fail.
21.
Run the
Cleaning Station Flow Calibration
wizard. Select
Print Care > Maintenance > Subsystem
Calibration Procedures > Imaging Oil Flow > Cleaning Station Flow Calibration Wizard
.
NOTE:
For tips on how to get the most out of the wizard, refer to
Calibrating cleaning station
imaging oil flow
(CA393-04840).
If the wizard does not work, perform manual Cleaning Station Flow Calibration:
NOTE:
Two people are needed for this task
a.
Verify that the press is in Standby.
b.
Verify that the PIP drum is disengaged.
Press in Shutdown
49