HP Indigo WS6600 Dripping Prevention and ITM Heating Hood Service -- CA393-101 - Page 32

Wiring the IHH blower

Get HP Indigo WS6600 PDF manuals and user guides View all HP Indigo WS6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

6. For presses with external IHH controller: Connect cable W2217 to the 5 pin socket of W2232, in the Nautilair suction blower bracket. For presses without external IHH controller: Connect cable W3162 to the 5 pin socket of W2232, in the Nautilair suction blower bracket. 7. For presses with external IHH controller: Connect cable W34 to the extension connector that is on cable W2217. For presses without external IHH controller: Connect cable W34 to the extension connector that is on cable W3162. 8. For presses with external IHH controller: Route the other end of W2217 cable down to the bottom of the PE chassis, through the channel at the base of the PE door frame, and up to the PDB. For presses without external IHH controller: Route the other end of W3162 cable down to the bottom of the PE chassis, through the channel at the base of the PE door frame, and up to the PDB. 9. For presses with external IHH controller: Connect the 2 wire branch of the W2217 to J23 on the PDB. For presses without external IHH controller: Connect the 2 wire branch of the W3162 to J23 on the PDB. Wiring the IHH blower Follow these steps in wiring the IHH blower. 1. For presses with external IHH controller: At the feed side, connect the small Mollex connector from cable W2223 (is not labeled) to the connector on the front of the IHH blower body. For presses without external IHH controller: At the feed side, connect the small Mollex connector from cable W3162 (is not labeled) to the connector on the front of the IHH blower body. 1 Side connector - W2223 PWR 2 Front connector - W2223 2. For presses with external IHH controller: Connect the molex connector from cable W2223 to the connector located on the side of the IHH blower body. For presses without external IHH controller: Connect the molex connector from cable W3162 to the connector located on the side of the IHH blower body. Wiring the IHH blower 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
6.
For presses with external IHH controller:
Connect cable
W2217
to the 5 pin socket of
W2232
, in the
Nautilair suction blower bracket.
For presses without external IHH controller:
Connect cable
W3162
to the 5 pin socket of
W2232
, in
the Nautilair suction blower bracket.
7.
For presses with external IHH controller:
Connect cable
W34
to the extension connector that is on
cable
W2217
.
For presses without external IHH controller:
Connect cable
W34
to the extension connector that is
on cable
W3162
.
8.
For presses with external IHH controller:
Route the other end of
W2217
cable down to the bottom of
the PE chassis, through the channel at the base of the PE door frame, and up to the PDB.
For presses without external IHH controller:
Route the other end of
W3162
cable down to the
bottom of the PE chassis, through the channel at the base of the PE door frame, and up to the PDB.
9.
For presses with external IHH controller:
Connect the 2 wire branch of the
W2217
to
J23
on the
PDB
.
For presses without external IHH controller:
Connect the 2 wire branch of the
W3162
to
J23
on the
PDB
.
Wiring the IHH blower
Follow these steps in wiring the IHH blower.
1.
For presses with external IHH controller:
At the feed side, connect the small Mollex connector from
cable
W2223
(is not labeled) to the connector on the front of the IHH blower body.
For presses without external IHH controller:
At the feed side, connect the small Mollex connector
from cable
W3162
(is not labeled) to the connector on the front of the IHH blower body.
1
Side connector — W2223 PWR
2
Front connector — W2223
2.
For presses with external IHH controller:
Connect the molex connector from cable
W2223
to the
connector located on the side of the IHH blower body.
For presses without external IHH controller:
Connect the molex connector from cable
W3162
to the
connector located on the side of the IHH blower body.
Wiring the IHH blower
29