HP Indigo WS6600 Dripping Prevention and ITM Heating Hood Service -- CA393-101 - Page 39

Baselining the dripping prevention kit, Special jigs and tools, Parts list

Get HP Indigo WS6600 PDF manuals and user guides View all HP Indigo WS6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

IHH troubleshooting ● Verify that the circuit breaker is on. ● During printing, verify that the IHH temperature (PV value) reaches ≈ 70° C (the temperature warms up from around 60° C). NOTE: When the press stops printing, the temperature may go up temporarily. ● PV value = s.err - indicates a sensor error. The temperature sensor and/or wiring may be disconnected or broken. Check the wiring , and replace the heater or wiring cable W2228 if needed ● PV value = e111 - indicates an internal error. Replace the IHH controller unit. ● PV value = h.err - indicates an internal error. Replace the IHH controller unit. ● PV value does not reach 70, and SV value = 70 during Print (remaining around the press temperature) - check that the circuit breaker is on, and that cables from IHH controller to the heater are connected properly. ● SV value does not change during Print - indicates that there is no communication between the IHH controller and the system. ● Stop LED remains on, OUT1 LED is off during Print - indicates that there is no communication between the IHH controller and the system. ● CMW value = OFF - IHH controller was not loaded with the required parameters. Replace the IHH controller unit. Baselining the dripping prevention kit It explains baselining the dripping prevention kit. Special jigs and tools List of special jigs and tools. ● Temperature and humidity meter ● Fluke DVM ● Conductivity meter ● Anemometer, model AMV-03 manufacturer: TES or PROVA Parts list It is recommended to have the following parts available on site when performing this procedure: ● 0905-1593 V-seal ● CA345-04606 Blade holder top assembly ● CA340-06873 EBV A/K & U/S rear-sealing ● CA341-06310 Suction hood bellows ● CA345-04644 Drain-top assy ● CT345-29733 CL ST main housing assembly kit 36 Chapter 3 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
IHH troubleshooting
●
Verify that the circuit breaker is on.
●
During printing, verify that the IHH temperature (PV value) reaches ≈ 70° C (the temperature warms up from
around 60° C).
NOTE:
When the press stops printing, the temperature may go up temporarily.
●
PV value = s.err
— indicates a sensor error. The temperature sensor and/or wiring may be disconnected or
broken. Check the wiring , and replace the heater or wiring cable W2228 if needed
●
PV value = e111
— indicates an internal error. Replace the IHH controller unit.
●
PV value = h.err
— indicates an internal error. Replace the IHH controller unit.
●
PV value does not reach 70, and SV value = 70
during Print (remaining around the press temperature) — check
that the circuit breaker is on, and that cables from IHH controller to the heater are connected properly.
●
SV value does not change during Print
— indicates that there is no communication between the IHH controller
and the system.
●
Stop LED remains on, OUT1 LED is off during Print
— indicates that there is no communication between the
IHH controller and the system.
●
CMW value = OFF
— IHH controller was not loaded with the required parameters. Replace the IHH controller
unit.
Baselining the dripping prevention kit
It explains baselining the dripping prevention kit.
Special jigs and tools
List of special jigs and tools.
●
Temperature and humidity meter
●
Fluke DVM
●
Conductivity meter
●
Anemometer, model AMV-03 manufacturer: TES or PROVA
Parts list
It is recommended to have the following parts available on site when performing this procedure:
●
0905-1593 V-seal
●
CA345-04606 Blade holder top assembly
●
CA340-06873 EBV A/K & U/S rear–sealing
●
CA341-06310 Suction hood bellows
●
CA345-04644 Drain–top assy
●
CT345-29733 CL ST main housing assembly kit
36
Chapter 3
Troubleshooting