HP LH4r Compaq 4000/7000 Racks Installation Guide - Page 24

Front of HP NetServer, Ribbon Cable

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Chapter 2 Preparing the HP NetServer 3. Grasp the LCD assembly with both hands. Pull up firmly on the LCD assembly to lift it as high as possible. You may need to pull quite firmly and wiggle the LCD assembly to overcome the retaining spring shown in Figure 2-11. When the LCD assembly is lifted high enough, the upper two posts on the HP NetServer are in the wide part of the upper two slots on the LCD cover, and the lower posts are free. When you feel that looseness, gently pull the LCD assembly away from the NetServer. Be careful not to damage the LCD cables. Retaining Spring Slots for Posts on Front of HP NetServer (4 Places) Twisted-Pair Cable LCD Rear Half of Existing LCD Cover Ribbon Cable LCD Board Front Half of Existing LCD Cover Figure 2-11. Disassembling the Existing LCD Assembly 4. Gently pull the LCD cables out through the hole in the processor tray. 5. To disassemble the LCD cover, gently push the face of the LCD into the LCD cover, as shown in Figure 2-11. The front half of the LCD cover detaches completely from the LCD board. Discard the front half of the LCD cover, but retain the LCD board. 6. Gently slide the LCD cables through the rear half of the LCD cover, as shown in Figure 2-11. Discard the rear half of the LCD cover, but retain the LCD board. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 2
Preparing the HP NetServer
20
3.
Grasp the LCD assembly with both hands. Pull up firmly on the LCD
assembly to lift it as high as possible. You may need to pull quite firmly
and wiggle the LCD assembly to overcome the retaining spring shown in
Figure 2-11.
When the LCD assembly is lifted high enough, the upper two posts on the
HP NetServer are in the wide part of the upper two slots on the LCD cover,
and the lower posts are free.
When you feel that looseness, gently pull the
LCD assembly away from the NetServer. Be careful not to damage the
LCD cables.
Rear Half
of Existing
LCD Cover
Front Half
of Existing
LCD Cover
Ribbon Cable
LCD Board
Twisted-Pair Cable
Slots for Posts on
Front of HP NetServer
(4 Places)
LCD
Retaining
Spring
Figure 2-11.
Disassembling the Existing LCD Assembly
4.
Gently pull the LCD cables out through the hole in the processor tray.
5.
To disassemble the LCD cover, gently push the face of the LCD into the
LCD cover, as shown in Figure 2-11. The front half of the LCD cover
detaches completely from the LCD board. Discard the front half of the
LCD cover, but retain the LCD board.
6.
Gently slide the LCD cables through the rear half of the LCD cover, as
shown in Figure 2-11. Discard the rear half of the LCD cover, but retain
the LCD board.