HP LH4r Compaq 4000/7000 Racks Installation Guide - Page 42

Reinstall Power Supply Modules, Install the Nameplate, HP NetServer LXr 8000 or HP NetServer LXr 8500.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Chapter 4 Installing into the Rack Reinstall Power Supply Modules Reinstall all power supply modules. To install a power supply module: 1. Pull down the handle on the new power supply module fully. 2. Insert the module in the power supply bay. 3. Slide the power supply module forward in the bay until it stops. 4. Lift the handle fully until it stops against the module. CAUTION When installing a power supply module, verify that the handle has latched the module fully into the power supply bay. An incorrectly-installed power supply module may cause data corruption or loss. Data corruption or loss due to an incorrectly-installed power supply module is not covered by the HP warranty. Install the Nameplate Prepare the Compaq rack-optimized front bezel by attaching the appropriate nameplate to it, as follows: 1. Orient the Compaq rack-optimized front bezel as shown in Figure 4-7. 2. From the kit, choose the nameplate for your model of HP NetServer, either HP NetServer LXr 8000 or HP NetServer LXr 8500. 3. Orient the nameplate with the HP logo on the left, as shown in Figure 4-7. 4. Insert the tab on the left end of the nameplate into the corresponding slot in the front bezel indicated in Figure 4-7. Bow the nameplate slightly, and insert the tab on the right end into the slot on the front bezel. 5. Align the three studs on the back of the nameplate with the corresponding holes in the front bezel. Press the nameplate against the front bezel until the studs lock into place. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 4
Installing into the Rack
38
Reinstall Power Supply Modules
Reinstall all power supply modules. To install a power supply module:
1.
Pull down the handle on the new power supply module fully.
2.
Insert the module in the power supply bay.
3.
Slide the power supply module forward in the bay until it stops.
4.
Lift the handle fully until it stops against the module.
CAUTION
When installing a power supply module, verify that the handle
has latched the module fully into the power supply bay.
An incorrectly-installed power supply module may cause data
corruption or loss. Data corruption or loss due to an
incorrectly-installed power supply module is not covered by
the HP warranty.
Install the Nameplate
Prepare the Compaq rack-optimized front bezel by attaching the appropriate
nameplate to it, as follows:
1. Orient the Compaq rack-optimized front bezel as shown in Figure 4-7.
2.
From the kit, choose the nameplate for your model of HP NetServer, either
HP NetServer LXr 8000 or HP NetServer LXr 8500.
3.
Orient the nameplate with the HP logo on the left, as shown in Figure 4-7.
4.
Insert the tab on the left end of the nameplate into the corresponding slot in
the front bezel indicated in Figure 4-7. Bow the nameplate slightly, and
insert the tab on the right end into the slot on the front bezel.
5.
Align the three studs on the back of the nameplate with the corresponding
holes in the front bezel. Press the nameplate against the front bezel until
the studs lock into place.