HP LH4r HP Netserver Service Handbook, Volume 1 - Low End - Page 38

I/O Board

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

I/O Board This HP NetServer contains six ISA- and PCI-compatible slots which provide the capability of adding accessory boards, such as disk controller boards and network interface boards. NOTE A board can be identified as ISA or PCI by the bracket-offset angle and the unique slot connector. System Board slot Slot 1- 16-bit ISA (half-length) or 32-bit PCI Slot 2- 32-bit PCI Slot 3- 32-bit PCI Slot 4- 16-bit ISA (half-length) or 32-bit PCI Slot 5- 16-bit ISA Slot 6- 16-bit ISA These slots allow you to install accessory boards as follows: • Slot 1 (the innermost) can be used for a short 16-bit ISA board or a 32-bit PCI board. • Slots 2 and 3 can be used for 32-bit PCI boards. • Slot 4 can be used for a full-length 16-bit ISA board or a 32-bit PCI board. • Slots 5 and 6 can be used for full-length 16-bit ISA boards The NetServer comes with a SCSI card preinstalled and configured in Slot 1, and network interface card preinstalled and configured in Slot 3. NOTE If you are manually configuring an accessory board, avoid using COM1 and COM4, if possible, due to the possibilities of resource conflicts with some application software programs. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
32
I/O Board
This HP NetServer contains six ISA- and PCI-compatible slots which provide the capability of adding
accessory boards, such as disk controller boards and network interface boards.
NOTE
A board can be identified as ISA or PCI by the bracket-offset angle and the unique
slot connector.
System Board slot
Slot 1— 16-bit ISA (half-length)
or 32-bit PCI
Slot 2— 32-bit PCI
Slot 3— 32-bit PCI
Slot 4— 16-bit ISA (half-length)
or 32-bit PCI
Slot 5— 16-bit ISA
Slot 6— 16-bit ISA
These slots allow you to install accessory boards as follows:
•
Slot 1 (the innermost) can be used for a short 16-bit ISA board or a 32-bit PCI board.
•
Slots 2 and 3 can be used for 32-bit PCI boards.
•
Slot 4 can be used for a full-length 16-bit ISA board or a 32-bit PCI board.
•
Slots 5 and 6 can be used for full-length 16-bit ISA boards
The NetServer comes with a SCSI card preinstalled and configured in Slot 1, and
network interface card
preinstalled and configured in Slot 3.
NOTE
If you are manually configuring an accessory board, avoid using COM1 and COM4, if
possible, due to the possibilities of resource conflicts with some application software
programs.