HP ML310 ProLiant ML310 Generation 2 Server User Guide - Page 41

Memory Options, DIMM Installation Guidelines

Get HP ML310 - ProLiant - G2 PDF manuals and user guides View all HP ML310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Hardware Options Installation 41 CAUTION: Heatsink retaining screws should be tightened in diagonally opposite pairs (in an "X" pattern). 7. Connect the fan cable to the system board. 8. Replace the access panel ("Removing the Access Panel" on page 22). Memory Options You can expand server memory by installing PC-3200 DDR SDRAM DIMMs with Advanced ECC. The system supports up to four DIMMs for a maximum of 4 GB. Refer to "System Board Components (on page 11)" for DIMM slot locations and bank assignments. DIMM Installation Guidelines Observe the following guidelines when installing additional memory: • DIMMs installed in the server must be Unbuffered DDR DRAM, 2.5 volts, 64 bits wide, and ECC. • If only a single DIMM is installed, it must be installed in slot 1A.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Hardware Options Installation
41
CAUTION:
Heatsink retaining screws should be tightened in
diagonally opposite pairs (in an "X" pattern).
7.
Connect the fan cable to the system board.
8.
Replace the access panel ("Removing the Access Panel" on page
22
).
Memory Options
You can expand server memory by installing PC-3200 DDR SDRAM DIMMs
with Advanced ECC. The system supports up to four DIMMs for a maximum of
4 GB.
Refer to "System Board Components (on page
11
)" for DIMM slot locations and
bank assignments.
DIMM Installation Guidelines
Observe the following guidelines when installing additional memory:
•
•
DIMMs installed in the server must be Unbuffered DDR DRAM, 2.5 volts,
64 bits wide, and ECC.
If only a single DIMM is installed, it must be installed in slot 1A.