HP Mini 1000 HP Mini 1000 NetBook - Maintenance and Service Guide - Page 44

and then detach the tape from the top of the, Disconnect the USB board pass-through cable - hard drive replacement

Get HP Mini 1000 - PC PDF manuals and user guides View all HP Mini 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

5. Grasp the Mylar tab on the drive, lift the drive up (4), and then slide it out of the drive bay. Reverse this procedure to install the hard drive. To remove the solid-state drive: 1. Release the ZIF connector (1) to which the USB board pass-through cable (that lies across the top of the drive) is attached. 2. Disconnect the USB board pass-through cable (2), and then detach the tape from the top of the drive. 3. Release the LIF connector (1) to which the solid-state drive cable is attached, and then disconnect the cable (2). 4. Remove the two black Phillips PM2.0×3.0 screws (3) that secure the drive bracket to the device. 36 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
5.
Grasp the Mylar tab on the drive, lift the drive up
(4)
, and then slide it out of the drive bay.
Reverse this procedure to install the hard drive.
To remove the solid-state drive:
1.
Release the ZIF connector
(1)
to which the USB board pass-through cable (that lies across the top
of the drive) is attached.
2.
Disconnect the USB board pass-through cable
(2)
, and then detach the tape from the top of the
drive.
3.
Release the LIF connector
(1)
to which the solid-state drive cable is attached, and then disconnect
the cable
(2)
.
4.
Remove the two black Phillips PM2.0×3.0 screws
(3)
that secure the drive bracket to the device.
36
Chapter 4
Removal and replacement procedures