HP Mini 1000 HP Mini 1000 NetBook - Maintenance and Service Guide - Page 49

CAUTION, Remove the WLAN module - restoration

Get HP Mini 1000 - PC PDF manuals and user guides View all HP Mini 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the device by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore device functionality, and then contact technical support through Help and Support. 1. Disconnect the wireless antenna cables (1) from the terminals on the WLAN module. 2. Remove the black Phillips PM2.0×3.0 screw (2) that secures the WLAN module to the system board. (The edge of the module opposite the slot rises away from the device.) 3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion. Reverse this procedure to install the WLAN module. Component replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
CAUTION:
To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the device by the governmental agency that regulates wireless devices in
your country or region. If you replace the module and then receive a warning message, remove the
module to restore device functionality, and then contact technical support through Help and Support.
1.
Disconnect the wireless antenna cables
(1)
from the terminals on the WLAN module.
2.
Remove the black Phillips PM2.0×3.0 screw
(2)
that secures the WLAN module to the system
board. (The edge of the module opposite the slot rises away from the device.)
3.
Remove the WLAN module
(3)
by pulling the module away from the slot at an angle.
NOTE:
WLAN modules are designed with a notch
(4)
to prevent incorrect insertion.
Reverse this procedure to install the WLAN module.
Component replacement procedures
41