Home » HP Manuals » Servers » HP NetServer LP 2000r » Manual Viewer

HP NetServer LP 2000r Installing IBM OS/2 on an HP Netserver - Page 20

C Remove the Drivers Diskette from drive A, and insert the Work Diskette 1. Delete

Get HP NetServer LP 2000r PDF manuals and user guides

View all HP NetServer LP 2000r manuals

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

MD HPTEMP CD HPTEMP B) Insert the "Drivers/Utilities" diskette in drive A of the workstation, and enter the following copy commands: COPY A:\7800\AIC7870.ADD COPY A:\7700\AIC7770.ADD COPY A:\HPDA\HPDA.ADD COPY A:\NETRAID\MRAID.ADD COPY A:\UPDATE.EXE C) Remove the Drivers Diskette from drive A, and insert the "Work Diskette 1". Delete the following files to make room on "Work Diskette 1" for new drivers by entering the following commands: DEL IBM2FLPY.ADD DEL IBM2ADSK.ADD DEL IBM2SCSI.ADD DEL AHA*.ADD Copy new drivers to "Work Diskette 1," by entering the following command: COPY *.* A:\ You may delete all the files in the C:\HPTEMP directory and also delete the C:\TEMP directory. Now you are ready to start the OS/2 Installation. Phase 3: Start Installation 5. Start installation of OS/2 using IBM "Installation" Diskette. To begin installing OS/2 Warp or OS/2 Warp Connect, place the Installation Diskette in drive A, insert the IBM OS/2 CD-ROM and boot the system. 6. Insert "Work Diskette 1" when prompted for IBM Diskette 1. When you are prompted to insert Diskette 1 and press Enter, insert the copy of "Work Diskette 1" created with the Drivers/Utility diskette, then press Enter. An OS/2 logo appears, and after some time you will see a screen titled "Welcome to OS/2". Press Enter again to continue. Select "Advanced Installation" if you want to partition your drives. Follow the prompts to create partitions as needed. 20

Section	Page
IBM OS/2 Installation Guide for all Hewlett-Packard NetServers	1
Introduction	1
Table of Contents	1
Before You Begin	2
Section 1. Installation Tips and Considerations	3
Tip 1) Extended Translation Setting	3
Tip 2) Extending Disk Capacity Beyond 1 GB	3
Tip 3) Formatting Disk Partitions Larger than 2 GB	4
Tip 4) Device Allocation under OS/2	4
Tip 5) RAM Greater Than 192 MB	4
Tip 6) Performance Tuning	4
Tip 7) Troubleshooting System Hangs When Loading CONFIG.SYS	5
Tip 8) OS/2 Warp Server Installation Issues	5
Tip 9) How to View the Resources Used by an Adapter	6
Tip 10) How to Run the HPVGSET.EXE Utility from the Navigator CD-ROM	7
Tip 11) 4GB RAM support in OS/2	7
Tip 12) HPFS386 Drive cache size issue on systems with 4GB RAM	8
Tip 13) When using HP NetRAID install the driver MRAID.ADD	8
Tip 14) Getting Trap 00D when booting OS/2	8
Tip 15) Getting Trap 008 during extensive disk/network I/O	8
Tip 16) Specific to E Series NetServers: How to boot from a NetRAID adapter while a 2910Bui SCSI card is present on the system	9
Tip 17) IRQ Sharing can cause system hangs	9
Tip 18) Adaptec driver AIC7870.ADD 133496 12-Jan-1998 or later is required for 2940UW with rev B chip set	9
Tip 19) Configuring IDE drives as boot device	9
Tip 20) NetServer LPr, LH 3 and LH 4 CD-ROM must be configured as \	10
Tip 21) NetServer LH 3 Embeded SCSI and Raid Adapter Configuration	10
Tip 22) Installing Multiple D5013 NICs	10
Tip 23) \	11
Tip 24) IBM's Recommended Procedure Installing OS/2 with New AIC78XX.ADD	11
Tip 25) NetServer E 60 - Fixpak 40 Required for Memory Dump Functionality	12
Considerations	12
Consideration 1: Choose the Booting Controller	12
Consideration 2: Selecting the Boot Drive Capacity	13
Consideration 3: Choosing the Boot Drive ID off Embedded Adaptec SCSI	13
Section 2. Creating the HP Drivers/Utilities Diskette	14
Procedure One	14
Procedure Two	15
Section 3. OS/2 CD-ROM Installation Procedures	16
Installing Warp 3.0 or Warp Conn. 3.0 or Warp Server 4.0	17
Detailed Procedure for Installing Warp 3.0, Warp Conn. & Warp Server 4.0	17
Installing Warp 4.0 or Warp Server SMP 4.0	25
Section 4. Installing Hewlett-Packard NIC's	32
Installing OS/2 LAN Services for use with the HP J2973A or J2970A 10BaseT PCI LAN Adapter (CD-ROM)	32
Installing LAPS Separately	33
HP J3171A/D5013A PCI Ethernet Adapters	35
General installation - LAN Server and OS/2 Requester (4.0 or 3.0)	35
Advanced Settings	36
Installing High Resolution Video Driver on a NetServer E 30, E 40, E 45	37
Installing High Resolution Video Driver on a NetServer E 60	38

Match case Limit results 1 per page

MD HPTEMP

CD HPTEMP

B) Insert the "Drivers/Utilities" diskette in drive A of the workstation, and enter the

following copy commands:

COPY A:\7800\AIC7870.ADD

COPY A:\7700\AIC7770.ADD

COPY A:\HPDA\HPDA.ADD

COPY A:\NETRAID\MRAID.ADD

COPY A:\UPDATE.EXE

C) Remove the Drivers Diskette from drive A, and insert the "Work Diskette 1". Delete the

following files to make room on "Work Diskette 1" for new drivers by entering the following

commands:

DEL IBM2FLPY.ADD

DEL IBM2ADSK.ADD

DEL IBM2SCSI.ADD

DEL AHA*.ADD

Copy new drivers to "Work Diskette 1," by entering the following command:

COPY *.* A:\

You may delete all the files in the C:\HPTEMP directory and also delete the C:\TEMP

directory.

Now you are ready to start the OS/2 Installation.

Phase 3: Start Installation

Start installation of OS/2 using IBM "Installation" Diskette.

To begin installing OS/2 Warp or OS/2 Warp Connect, place the Installation Diskette in

drive A, insert the IBM OS/2 CD-ROM and boot the system.

Insert "Work Diskette 1" when prompted for IBM Diskette 1.

When you are prompted to insert Diskette 1 and press Enter, insert the copy of "Work

Diskette 1" created with the Drivers/Utility diskette, then press Enter. An OS/2 logo appears,

and after some time you will see a screen titled "Welcome to OS/2". Press Enter again to

continue.

Select "Advanced Installation" if you want to partition your drives. Follow the prompts to

create partitions as needed.