HP OmniBook 900 HP OmniBook 900 Reference Guide - Page 80

To replace the hard disk drive holder

Get HP OmniBook 900 - Notebook PC PDF manuals and user guides View all HP OmniBook 900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Important Expanding the OmniBook Installing a Hard Disk Drive If you are installing a new hard disk drive, you should create a Hibernate partition on the drive before loading any software. See "To recover the factory installation of Windows" on page 118. To replace the hard disk drive holder If you are installing a new hard drive that does not have a cover, you can remove the cover parts from the old hard drive. You'll need a small Phillips screwdriver for this procedure. 1. Carefully pry the connector off the end of the hard disk drive. Work alternately at each end so that the connector slides off evenly. 2. Remove the two screws from the case, as shown. 3. Lift the plastic tab and remove the plastic cover and metal sheet from the hard disk drive. The metal sheet may not be present on some drives. When you reinstall the connector, make sure the small tabs on the side of the connector hold the metal sheet. 80 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Expanding the OmniBook
Installing a Hard Disk Drive
80
Reference Guide
Important
If you are installing a new hard disk drive, you should create a Hibernate partition on the
drive before loading any software. See “To recover the factory installation of Windows”
on page 118.
To replace the hard disk drive holder
If you are installing a new hard drive that does not have a cover, you can remove the
cover parts from the old hard drive. You’ll need a small Phillips screwdriver for this
procedure.
1.
Carefully pry the connector off the end of the hard disk drive. Work alternately at
each end so that the connector slides off evenly.
2.
Remove the two screws from the case, as shown.
3.
Lift the plastic tab and remove the plastic cover and metal sheet from the hard disk
drive. The metal sheet may not be present on some drives.
When you reinstall the connector, make sure the small tabs on the side of the connector
hold the metal sheet.