HP Pavilion 14-ab000 ab000 through 14 - ab099 Maintenance and Service Guide - Page 69

Release the WLAN transceivers, Remove the WLAN module antenna cable

Get HP Pavilion 14-ab000 PDF manuals and user guides View all HP Pavilion 14-ab000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

3. Remove cable from display enclosure (3). Remove the display panel hinges: 1. Remove the two Phillips PM1.9×3.5 screws (1) that secure the hinges to the display enclosure. 2. Remove the two Phillips PM2.5×3.22 broad head screws (2) that secure the hinges to the display enclosure. 3. Remove the two Phillips PM2.4×4.7 screws (3) that secure the hinges to the display enclosure. 4. Remove the hinges from display enclosure (4). Remove the WLAN module antenna cable: 1. Release the WLAN transceivers (1). CAUTION: The transceivers are attached to the display enclosure with adhesive. To avoid damaging the components, use only gentle pressure when removing them from the enclosure. 2. Release the antenna cable from the routing clips on the right side of the enclosure (2). Component replacement procedures 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
3.
Remove cable from display enclosure
(3)
.
Remove the display panel hinges:
1.
Remove the two Phillips PM1.9×3.5 screws
(1)
that secure the hinges to the display enclosure.
2.
Remove the two Phillips PM2.5×3.22 broad head screws
(2)
that secure the hinges to the display
enclosure.
3.
Remove the two Phillips PM2.4×4.7 screws
(3)
that secure the hinges to the display enclosure.
4.
Remove the hinges from display enclosure
(4)
.
Remove the WLAN module antenna cable:
1.
Release the WLAN transceivers
(1)
.
CAUTION:
The transceivers are attached to the display enclosure with adhesive. To avoid damaging
the components, use only gentle pressure when removing them from the enclosure.
2.
Release the antenna cable from the routing clips on the right side of the enclosure
(2)
.
Component replacement procedures
59