HP ProLiant ML310e HP ProLiant ML310e Gen8 Server User Guide - Page 33

Drive cage options, Four-bay LFF hot-plug drive backplane option

Get HP ProLiant ML310e PDF manuals and user guides View all HP ProLiant ML310e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

3. Prepare the drive. 4. Install the drive. 5. Determine the status of the drive from the drive LED definitions (on page 15). 6. Close and lock the tower bezel. Drive cage options Four-bay LFF hot-plug drive backplane option To install the component: 1. Power down the server (on page 18). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Remove the tower bezel (on page 19). 4. Remove the access panel (on page 20). 5. If the drives are to be connected to a storage controller card, remove the air baffle (on page 21). 6. Remove all installed drives. Hardware options installation 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Hardware options installation 33
3.
Prepare the drive.
4.
Install the drive.
5.
Determine the status of the drive from the drive LED definitions (on page
15
).
6.
Close and lock the tower bezel.
Drive cage options
Four-bay LFF hot-plug drive backplane option
To install the component:
1.
Power down the server (on page
18
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Remove the tower bezel (on page
19
).
4.
Remove the access panel (on page
20
).
5.
If the drives are to be connected to a storage controller card, remove the air baffle (on page
21
).
6.
Remove all installed drives.