HP ProLiant ML330e Compaq ProLiant ML330e/ ML330 Server Maintenance and Servic - Page 18

Front Bezel

Get HP ProLiant ML330e PDF manuals and user guides View all HP ProLiant ML330e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Removal and Replacement Procedures 2-5 Front Bezel WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. To remove the front bezel: 1. Complete the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Pull forward on the latch at the bottom of the front bezel . 3. Swing the front bezel upward, and then slide it out and away from the chassis . 1 2 Figure 2-1. Removing the front bezel NOTE: When replacing the front bezel, ensure that the top hinge points are properly placed in the chassis before rotating the front bezel back into its original position. NOTE: Intruder Alert enables and disables the intruder alert option. When enabled, an intruder alert message is displayed if the front bezel has been unlatched or removed. The default setting is disabled. To replace the front bezel, reverse steps 2 and 3.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Removal and Replacement Procedures
2-5
Front Bezel
WARNING:
To reduce the risk of personal injury and to prevent damage to the equipment,
before removing the front bezel, make sure that the server is powered down, all cables are
disconnected from the back of the server, and the power cord is disconnected from the
grounded (earthed) AC outlet.
To remove the front bezel:
1. Complete the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2. Pull forward on the latch at the bottom of the front bezel
.
3. Swing the front bezel upward, and then slide it out and away from the chassis
.
1
2
Figure 2-1.
Removing the front bezel
NOTE:
When replacing the front bezel, ensure that the top hinge points are properly placed in the
chassis before rotating the front bezel back into its original position.
NOTE:
Intruder Alert enables and disables the intruder alert option. When enabled, an intruder alert
message is displayed if the front bezel has been unlatched or removed. The default setting is disabled.
To replace the front bezel, reverse steps 2 and 3.