HP ProLiant ML330e Compaq ProLiant ML330e/ ML330 Server Maintenance and Servic - Page 22

Drive Tray, out of the front of the chassis

Get HP ProLiant ML330e PDF manuals and user guides View all HP ProLiant ML330e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Removal and Replacement Procedures 2-9 Drive Tray To remove a drive tray from a removable media bay: WARNING: To reduce the risk of personal injury and to prevent damage to the equipment, before removing the access panel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. NOTE: The drive trays in the removable media bays can be used to mount internal 3.5-inch hard drives. 1. Complete the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the front bezel. See "Front Bezel" earlier in this chapter. 3. Remove the access panel. See "Access Panel" earlier in this chapter. 4. Remove the screws on either side of the drive tray , and then gently slide the drive tray out of the front of the chassis . 2 1 1 Figure 2-5. Removing a drive tray To replace a drive tray, reverse steps 2 through 4.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Removal and Replacement Procedures
2-9
Drive Tray
To remove a drive tray from a removable media bay:
WARNING:
To reduce the risk of personal injury and to prevent damage to the equipment,
before removing the access panel, make sure that the server is powered down, all cables are
disconnected from the back of the server, and the power cord is disconnected from the
grounded (earthed) AC outlet.
NOTE:
The drive trays in the removable media bays can be used to mount internal 3.5-inch hard drives.
1. Complete the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2. Remove the front bezel. See
“
Front Bezel
”
earlier in this chapter.
3. Remove the access panel. See
“
Access Panel
”
earlier in this chapter.
4. Remove the screws on either side of the drive tray
, and then gently slide the drive tray
out of the front of the chassis
.
1
1
2
Figure 2-5.
Removing a drive tray
To replace a drive tray, reverse steps 2 through 4.