HP ProOne 600 Maintenance & Service Guide HP ProOne 600 G1 All-in-One - Page 93

Updating the display panel manufacturer setting in BIOS, LVDS Panel Select, Advanced, Device Options

Get HP ProOne 600 PDF manuals and user guides View all HP ProOne 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Route the following cables from under the power supply: ● Power button board ● Hard drive data (SATA) ● Hard drive power ● Hood sensor Updating the display panel manufacturer setting in BIOS After replacing the system board, make sure the display panel manufacturer setting is correct in BIOS. If the incorrect panel manufacturer is set in BIOS, the display panel may function incorrectly. The display panel manufacturer is identified on the jumper setting label on the base pan. After confirming the manufacturer of the display panel on the computer, go into BIOS and make sure the LVDS Panel Select setting is correct. To update BIOS with display panel model information: 1. Boot the computer. 2. Repeatedly press F10 when the monitor light turns green to access the F10 Setup utility. 3. Select Advanced, select Device Options, select LVDS Panel Select, and then select the manufacturer for the new display panel. 4. Save your settings, exit F10 Setup, and allow the computer to continue to the operating system. When you change the LVDS setting to the installed panel type, the BIOS reprograms the EDID with the correct data. You must set the panel before the Auto-select setting functions correctly. System board 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Route the following cables from under the power supply:
●
Power button board
●
Hard drive data (SATA)
●
Hard drive power
●
Hood sensor
Updating the display panel manufacturer setting in BIOS
After replacing the system board, make sure the display panel manufacturer setting is correct in BIOS. If
the incorrect panel manufacturer is set in BIOS, the display panel may function incorrectly.
The display panel manufacturer is identified on the jumper setting label on the base pan.
After confirming the manufacturer of the display panel on the computer, go into BIOS and make sure
the
LVDS Panel Select
setting is correct.
To update BIOS with display panel model information:
1.
Boot the computer.
2.
Repeatedly press
F10
when the monitor light turns green to access the F10 Setup utility.
3.
Select
Advanced
, select
Device Options
, select
LVDS Panel Select
, and then select the
manufacturer for the new display panel.
4.
Save your settings, exit F10 Setup, and allow the computer to continue to the operating system.
When you change the LVDS setting to the installed panel type, the BIOS reprograms the EDID with the
correct data. You must set the panel before the Auto-select setting functions correctly.
System board
83