HP ScanJet Enterprise Flow 5000 User Guide - Page 16

before loading them into the document input tray.

Get HP ScanJet Enterprise Flow 5000 PDF manuals and user guides View all HP ScanJet Enterprise Flow 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Minimum weight: Maximum weight: 162 g/m2 (8 points or 60 lb) 326 g/m2 (15 points or 120 lb) ● Scanning the following types of documents might result in paper jams or damage to the documents. Wrinkled or creased documents Curled documents Torn documents (including those torn from spiral notebooks) Carbon paper Documents with paper clips or staples Coated paper Extremely thin, translucent paper Photos Paper with adhesive notes or flags attached Overhead transparencies Papers that are stuck together Paper where the toner has not fully dried, or with wet substances such as glue or correction fluid ● Smooth out any folds or curls in your documents before placing them into the document input tray. If the leading edge of a document is curled or folded, it may cause a paper jam. ● When loading paper that is smaller than 74 mm (2.9 in) in one dimension (such as business cards), place the pages with the long side parallel to the paper guides. ● To scan fragile documents (such as photos or documents on wrinkled or very lightweight paper), place the document in a clear, heavyweight document sleeve no wider than 216 mm (8.5 in) before loading them into the document input tray. TIP: If you do not have an appropriately sized document sleeve, consider using a sleeve intended for use in a ring binder. Trim the ring-side edge so the sleeve is no more than 216 mm (8.5 in) wide. ● Make sure that the hatch on the document feeder is securely latched. To properly close the hatch, press until you hear a click. ● Adjust the paper guides to the width of the documents. Make sure that the paper guides touch the edges of the original. If there is any clearance between the paper guides and the edges of the documents, the scanned image might be skewed. ● When scanning a stack of mixed-width pages, center-justify the stack. Be aware that pages narrower than the maximum width in the stack may skew. 10 Chapter 2 Use the scanner ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Minimum weight:
162 g/m
2
(8 points or 60 lb)
Maximum weight:
326 g/m
2
(15 points or 120 lb)
●
Scanning the following types of documents might result in paper jams or damage to the
documents.
Wrinkled or creased documents
Curled documents
Torn documents (including those torn
from spiral notebooks)
Documents with paper clips or staples
Carbon paper
Coated paper
Extremely thin, translucent paper
Paper with adhesive notes or flags
attached
Photos
Overhead transparencies
Papers that are stuck together
Paper where the toner has not fully
dried, or with wet substances such as
glue or correction fluid
●
Smooth out any folds or curls in your documents before placing them into the document input tray.
If the leading edge of a document is curled or folded, it may cause a paper jam.
●
When loading paper that is smaller than 74 mm (2.9 in) in one dimension (such as business
cards), place the pages with the long side parallel to the paper guides.
●
To scan fragile documents (such as photos or documents on wrinkled or very lightweight paper),
place the document in a clear, heavyweight document sleeve no wider than 216 mm (8.5 in)
before loading them into the document input tray.
TIP:
If you do not have an appropriately sized document sleeve, consider using a sleeve
intended for use in a ring binder. Trim the ring-side edge so the sleeve is no more than 216 mm
(8.5 in) wide.
●
Make sure that the hatch on the document feeder is securely latched. To properly close the hatch,
press until you hear a click.
●
Adjust the paper guides to the width of the documents. Make sure that the paper guides touch the
edges of the original. If there is any clearance between the paper guides and the edges of the
documents, the scanned image might be skewed.
●
When scanning a stack of mixed-width pages, center-justify the stack. Be aware that pages
narrower than the maximum width in the stack may skew.
10
Chapter 2
Use the scanner
ENWW