HP VL400 hp vectra vl400 (automatic), Image Library administrator's version CD - Page 34

Installing Components Without the User Interface, Troubleshooting, Log File, Information

Get HP VL400 - Vectra - 64 MB RAM PDF manuals and user guides View all HP VL400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2 Local Automatic Installation Installing Components Without the User Interface Installing Components Without the User Interface You can install individual drivers or software utilities from the Image Library CD-ROM. To do this, locate the desired component for your operating system, then run the Setup.exe file. For more information about the directory structure of the CD-ROM, refer to page 14. Log File Troubleshooting Information Troubleshooting • If you encountered any problems installing a component, you can try to install it manually using the installation files that were copied to the target PC's hard disk in the \Masters directory. • If you encountered any problems installing the LAN driver, you must first remove the driver before trying to install it again. For example, to do this in Windows NT 4.0, click Start  Settings  Control Panel, double-click Network, click the Adapters tab, select the driver and click Remove. After each component installation, the Image Library verifies that the component installed correctly. These results are written in the log file (ImageLibrary.log, located in the hard drive's root directory). In fact, the log file contains a complete trace of the installation process. Therefore you should consult the log file for valuable troubleshooting information. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
2
Local Automatic Installation
Installing Components Without the User Interface
34
Installing Components Without the User Interface
You can install individual drivers or software utilities from the Image
Library CD-ROM. To do this, locate the desired component for your
operating system, then run the
Setup.exe
file.
For more information about the directory structure of the CD-ROM,
refer to page 14.
Troubleshooting
•
If you encountered any problems installing a component, you can try
to install it manually using the installation files that were copied to
the target PC’s hard disk in the
\Masters
directory.
•
If you encountered any problems installing the LAN driver, you must
first remove the driver before trying to install it again. For example,
to do this in Windows NT 4.0, click
Start
±
Settings
±
Control
Panel
, double-click
Network
, click the
Adapters
tab, select the
driver and click
Remove
.
Log File
Troubleshooting
Information
After each component installation, the Image Library verifies that the
component installed correctly. These results are written in the log file
(
ImageLibrary.log
, located in the hard drive’s root directory).
In fact, the log file contains a complete trace of the installation process.
Therefore you should consult the log file for valuable troubleshooting
information.